1 .\"
   2 .\" This file and its contents are supplied under the terms of the
   3 .\" Common Development and Distribution License ("CDDL"), version 1.0.
   4 .\" You may only use this file in accordance with the terms of version
   5 .\" 1.0 of the CDDL.
   6 .\"
   7 .\" A full copy of the text of the CDDL should have accompanied this
   8 .\" source.  A copy of the CDDL is also available via the Internet at
   9 .\" http://www.illumos.org/license/CDDL.
  10 .\"
  11 .\"
  12 .\" Copyright (C) 2013 Hewlett-Packard Development Company, L.P.
  13 .\"
  14 .TH CPQARY3 7D Aug 26, 2013"
  15 .SH NAME
  16 .LP
  17 cpqary3 - provides disk and SCSI tape support for HP Smart Array controllers
  18 .LP
  19 .SH DESCRIPTION
  20 .LP
  21 The cpqary3 module provides low-level interface routines between the common
  22 disk I/O subsystem and the HP SMART Array controllers. The cpqary3 driver
  23 provides disk and SCSI tape support for the HP Smart Array controllers.
  24 .LP
  25 Please refer to the cpqary3 release notes, for the supported HP Smart Array
  26 Controllers and Storage boxes.
  27 .LP
  28 Each controller should be the sole initiator on a SCSI bus. Auto
  29 configuration code determines if the adapter is present at the Configured
  30 address and what types of devices are attached to it.
  31 .SH CONFIGURATION
  32 Use the Array Configuration Utility to configure the controllers. Each
  33 controller can support up to 32 logical volumes. In addition, each controller
  34 supports up to a maximum of 28 connected SCSI tape drives.
  35 With 1.90 and later versions of cpqary3 driver, HP Smart Array SAS controllers,
  36 having Firmware Revision 5.10 or later, will support 64 logical drives. This
  37 firmware also supports Dual Domian Multipath configurations.
  38 .LP

  61 \&'scsi' class, where N is the total number of SCSI tape drives connected to the
  62 controller with largest number of tape drives connected to it, in the existing
  63 configuration. For example, two supported controller, c1 and c2 are present in
  64 the system. If controller c1 has two (2) tape drives and controller c2 has five
  65 (5) tape drives connected, then entries for target IDs 33 thru 38 are required
  66 under 'scsi' class in /kernel/drv/st.conf file. The maximum number of tape
  67 drives that can be connected to a controller is 28. With 1.90 and later versions
  68 of cpqary3 driver, if tape drives are connected to Smart Array SAS controllers,
  69 then target ID entries for tape drives from 65 to 65+N must be added in
  70 /kernel/drv/st.conf file under the \&'scsi' class.
  71 .SH FILES
  72 .PD 0
  73 .TP 25
  74 .B /kernel/drv/cpqary3.conf
  75 - configuration file for CPQary3
  76 .PD
  77 .SH "SEE ALSO"
  78 .BR driver.conf (4),
  79 .BR sd (7D),
  80 .BR st (7D)
  81 .LP
  82 .SH NOTES
  83 .LP
  84 The Smart Array controllers supported by the current version of the
  85 cpqary3 driver do not support 'format unit' SCSI command. Hence, selecting
  86 \&'format' option under 'format' utility main menu is not supported. In addition,
  87 the 'repair' option under 'format' utility main menu is not supported as this
  88 operation is not applicable to Logical volumes connected to the supported Smart
  89 Array controllers.

   1 .\"
   2 .\" This file and its contents are supplied under the terms of the
   3 .\" Common Development and Distribution License ("CDDL"), version 1.0.
   4 .\" You may only use this file in accordance with the terms of version
   5 .\" 1.0 of the CDDL.
   6 .\"
   7 .\" A full copy of the text of the CDDL should have accompanied this
   8 .\" source.  A copy of the CDDL is also available via the Internet at
   9 .\" http://www.illumos.org/license/CDDL.
  10 .\"
  11 .\"
  12 .\" Copyright (C) 2013 Hewlett-Packard Development Company, L.P.
  13 .\"
  14 .TH CPQARY3 7D Aug 26, 2013"
  15 .SH NAME

  16 cpqary3 - provides disk and SCSI tape support for HP Smart Array controllers

  17 .SH DESCRIPTION
  18 .LP
  19 The cpqary3 module provides low-level interface routines between the common
  20 disk I/O subsystem and the HP SMART Array controllers. The cpqary3 driver
  21 provides disk and SCSI tape support for the HP Smart Array controllers.
  22 .LP
  23 Please refer to the cpqary3 release notes, for the supported HP Smart Array
  24 Controllers and Storage boxes.
  25 .LP
  26 Each controller should be the sole initiator on a SCSI bus. Auto
  27 configuration code determines if the adapter is present at the Configured
  28 address and what types of devices are attached to it.
  29 .SH CONFIGURATION
  30 Use the Array Configuration Utility to configure the controllers. Each
  31 controller can support up to 32 logical volumes. In addition, each controller
  32 supports up to a maximum of 28 connected SCSI tape drives.
  33 With 1.90 and later versions of cpqary3 driver, HP Smart Array SAS controllers,
  34 having Firmware Revision 5.10 or later, will support 64 logical drives. This
  35 firmware also supports Dual Domian Multipath configurations.
  36 .LP

  59 \&'scsi' class, where N is the total number of SCSI tape drives connected to the
  60 controller with largest number of tape drives connected to it, in the existing
  61 configuration. For example, two supported controller, c1 and c2 are present in
  62 the system. If controller c1 has two (2) tape drives and controller c2 has five
  63 (5) tape drives connected, then entries for target IDs 33 thru 38 are required
  64 under 'scsi' class in /kernel/drv/st.conf file. The maximum number of tape
  65 drives that can be connected to a controller is 28. With 1.90 and later versions
  66 of cpqary3 driver, if tape drives are connected to Smart Array SAS controllers,
  67 then target ID entries for tape drives from 65 to 65+N must be added in
  68 /kernel/drv/st.conf file under the \&'scsi' class.
  69 .SH FILES
  70 .PD 0
  71 .TP 25
  72 .B /kernel/drv/cpqary3.conf
  73 - configuration file for CPQary3
  74 .PD
  75 .SH "SEE ALSO"
  76 .BR driver.conf (4),
  77 .BR sd (7D),
  78 .BR st (7D)

  79 .SH NOTES
  80 .LP
  81 The Smart Array controllers supported by the current version of the
  82 cpqary3 driver do not support 'format unit' SCSI command. Hence, selecting
  83 \&'format' option under 'format' utility main menu is not supported. In addition,
  84 the 'repair' option under 'format' utility main menu is not supported as this
  85 operation is not applicable to Logical volumes connected to the supported Smart
  86 Array controllers.