1 /******************************************************************************
2
3 Copyright (c) 2001-2012, Intel Corporation
4 All rights reserved.
5
6 Redistribution and use in source and binary forms, with or without
7 modification, are permitted provided that the following conditions are met:
8
9 1. Redistributions of source code must retain the above copyright notice,
10 this list of conditions and the following disclaimer.
11
12 2. Redistributions in binary form must reproduce the above copyright
13 notice, this list of conditions and the following disclaimer in the
14 documentation and/or other materials provided with the distribution.
15
16 3. Neither the name of the Intel Corporation nor the names of its
17 contributors may be used to endorse or promote products derived from
18 this software without specific prior written permission.
19
20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
30 POSSIBILITY OF SUCH DAMAGE.
31
32 ******************************************************************************/
33 /*$FreeBSD: src/sys/dev/ixgbe/ixgbe_82599.c,v 1.8 2012/07/05 20:51:44 jfv Exp $*/
34
35 #include "ixgbe_type.h"
36 #include "ixgbe_82599.h"
37 #include "ixgbe_api.h"
38 #include "ixgbe_common.h"
39 #include "ixgbe_phy.h"
40
41 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
42 ixgbe_link_speed speed,
43 bool autoneg,
44 bool autoneg_wait_to_complete);
45 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw);
46 static s32 ixgbe_read_eeprom_82599(struct ixgbe_hw *hw,
47 u16 offset, u16 *data);
48 static s32 ixgbe_read_eeprom_buffer_82599(struct ixgbe_hw *hw, u16 offset,
49 u16 words, u16 *data);
50
51 void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)
52 {
53 struct ixgbe_mac_info *mac = &hw->mac;
54
55 DEBUGFUNC("ixgbe_init_mac_link_ops_82599");
56
57 /* enable the laser control functions for SFP+ fiber */
58 if (mac->ops.get_media_type(hw) == ixgbe_media_type_fiber) {
59 mac->ops.disable_tx_laser =
60 &ixgbe_disable_tx_laser_multispeed_fiber;
61 mac->ops.enable_tx_laser =
62 &ixgbe_enable_tx_laser_multispeed_fiber;
63 mac->ops.flap_tx_laser = &ixgbe_flap_tx_laser_multispeed_fiber;
64
65 } else {
66 mac->ops.disable_tx_laser = NULL;
67 mac->ops.enable_tx_laser = NULL;
68 mac->ops.flap_tx_laser = NULL;
69 }
70
71 if (hw->phy.multispeed_fiber) {
72 /* Set up dual speed SFP+ support */
73 mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber;
74 } else {
75 if ((ixgbe_get_media_type(hw) == ixgbe_media_type_backplane) &&
76 (hw->phy.smart_speed == ixgbe_smart_speed_auto ||
77 hw->phy.smart_speed == ixgbe_smart_speed_on) &&
78 !ixgbe_verify_lesm_fw_enabled_82599(hw)) {
79 mac->ops.setup_link = &ixgbe_setup_mac_link_smartspeed;
80 } else {
81 mac->ops.setup_link = &ixgbe_setup_mac_link_82599;
82 }
83 }
84 }
85
86 /**
87 * ixgbe_init_phy_ops_82599 - PHY/SFP specific init
88 * @hw: pointer to hardware structure
89 *
90 * Initialize any function pointers that were not able to be
91 * set during init_shared_code because the PHY/SFP type was
92 * not known. Perform the SFP init if necessary.
93 *
94 **/
95 s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw)
96 {
97 struct ixgbe_mac_info *mac = &hw->mac;
98 struct ixgbe_phy_info *phy = &hw->phy;
99 s32 ret_val = IXGBE_SUCCESS;
100
101 DEBUGFUNC("ixgbe_init_phy_ops_82599");
102
103 /* Identify the PHY or SFP module */
104 ret_val = phy->ops.identify(hw);
105 if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED)
106 goto init_phy_ops_out;
107
108 /* Setup function pointers based on detected SFP module and speeds */
109 ixgbe_init_mac_link_ops_82599(hw);
110 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown)
111 hw->phy.ops.reset = NULL;
112
113 /* If copper media, overwrite with copper function pointers */
114 if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
115 mac->ops.setup_link = &ixgbe_setup_copper_link_82599;
116 mac->ops.get_link_capabilities =
117 &ixgbe_get_copper_link_capabilities_generic;
118 }
119
120 /* Set necessary function pointers based on phy type */
121 switch (hw->phy.type) {
122 case ixgbe_phy_tn:
123 phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
124 phy->ops.check_link = &ixgbe_check_phy_link_tnx;
125 phy->ops.get_firmware_version =
126 &ixgbe_get_phy_firmware_version_tnx;
127 break;
128 default:
129 break;
130 }
131 init_phy_ops_out:
132 return ret_val;
133 }
134
135 s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw)
136 {
137 s32 ret_val = IXGBE_SUCCESS;
138 u32 reg_anlp1 = 0;
139 u32 i = 0;
140 u16 list_offset, data_offset, data_value;
141
142 DEBUGFUNC("ixgbe_setup_sfp_modules_82599");
143
144 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) {
145 ixgbe_init_mac_link_ops_82599(hw);
146
147 hw->phy.ops.reset = NULL;
148
149 ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset,
150 &data_offset);
151 if (ret_val != IXGBE_SUCCESS)
152 goto setup_sfp_out;
153
154 /* PHY config will finish before releasing the semaphore */
155 ret_val = hw->mac.ops.acquire_swfw_sync(hw,
156 IXGBE_GSSR_MAC_CSR_SM);
157 if (ret_val != IXGBE_SUCCESS) {
158 ret_val = IXGBE_ERR_SWFW_SYNC;
159 goto setup_sfp_out;
160 }
161
162 hw->eeprom.ops.read(hw, ++data_offset, &data_value);
163 while (data_value != 0xffff) {
164 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, data_value);
165 IXGBE_WRITE_FLUSH(hw);
166 hw->eeprom.ops.read(hw, ++data_offset, &data_value);
167 }
168
169 /* Release the semaphore */
170 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
171 /* Delay obtaining semaphore again to allow FW access */
172 msec_delay(hw->eeprom.semaphore_delay);
173
174 /* Now restart DSP by setting Restart_AN and clearing LMS */
175 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, ((IXGBE_READ_REG(hw,
176 IXGBE_AUTOC) & ~IXGBE_AUTOC_LMS_MASK) |
177 IXGBE_AUTOC_AN_RESTART));
178
179 /* Wait for AN to leave state 0 */
180 for (i = 0; i < 10; i++) {
181 msec_delay(4);
182 reg_anlp1 = IXGBE_READ_REG(hw, IXGBE_ANLP1);
183 if (reg_anlp1 & IXGBE_ANLP1_AN_STATE_MASK)
184 break;
185 }
186 if (!(reg_anlp1 & IXGBE_ANLP1_AN_STATE_MASK)) {
187 DEBUGOUT("sfp module setup not complete\n");
188 ret_val = IXGBE_ERR_SFP_SETUP_NOT_COMPLETE;
189 goto setup_sfp_out;
190 }
191
192 /* Restart DSP by setting Restart_AN and return to SFI mode */
193 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, (IXGBE_READ_REG(hw,
194 IXGBE_AUTOC) | IXGBE_AUTOC_LMS_10G_SERIAL |
195 IXGBE_AUTOC_AN_RESTART));
196 }
197
198 setup_sfp_out:
199 return ret_val;
200 }
201
202 /**
203 * ixgbe_init_ops_82599 - Inits func ptrs and MAC type
204 * @hw: pointer to hardware structure
205 *
206 * Initialize the function pointers and assign the MAC type for 82599.
207 * Does not touch the hardware.
208 **/
209
210 s32 ixgbe_init_ops_82599(struct ixgbe_hw *hw)
211 {
212 struct ixgbe_mac_info *mac = &hw->mac;
213 struct ixgbe_phy_info *phy = &hw->phy;
214 struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
215 s32 ret_val;
216
217 DEBUGFUNC("ixgbe_init_ops_82599");
218
219 ret_val = ixgbe_init_phy_ops_generic(hw);
220 ret_val = ixgbe_init_ops_generic(hw);
221
222 /* PHY */
223 phy->ops.identify = &ixgbe_identify_phy_82599;
224 phy->ops.init = &ixgbe_init_phy_ops_82599;
225
226 /* MAC */
227 mac->ops.reset_hw = &ixgbe_reset_hw_82599;
228 mac->ops.enable_relaxed_ordering = &ixgbe_enable_relaxed_ordering_gen2;
229 mac->ops.get_media_type = &ixgbe_get_media_type_82599;
230 mac->ops.get_supported_physical_layer =
231 &ixgbe_get_supported_physical_layer_82599;
232 mac->ops.disable_sec_rx_path = &ixgbe_disable_sec_rx_path_generic;
233 mac->ops.enable_sec_rx_path = &ixgbe_enable_sec_rx_path_generic;
234 mac->ops.enable_rx_dma = &ixgbe_enable_rx_dma_82599;
235 mac->ops.read_analog_reg8 = &ixgbe_read_analog_reg8_82599;
236 mac->ops.write_analog_reg8 = &ixgbe_write_analog_reg8_82599;
237 mac->ops.start_hw = &ixgbe_start_hw_82599;
238 mac->ops.get_san_mac_addr = &ixgbe_get_san_mac_addr_generic;
239 mac->ops.set_san_mac_addr = &ixgbe_set_san_mac_addr_generic;
240 mac->ops.get_device_caps = &ixgbe_get_device_caps_generic;
241 mac->ops.get_wwn_prefix = &ixgbe_get_wwn_prefix_generic;
242 mac->ops.get_fcoe_boot_status = &ixgbe_get_fcoe_boot_status_generic;
243
244 /* RAR, Multicast, VLAN */
245 mac->ops.set_vmdq = &ixgbe_set_vmdq_generic;
246 mac->ops.set_vmdq_san_mac = &ixgbe_set_vmdq_san_mac_generic;
247 mac->ops.clear_vmdq = &ixgbe_clear_vmdq_generic;
248 mac->ops.insert_mac_addr = &ixgbe_insert_mac_addr_generic;
249 mac->rar_highwater = 1;
250 mac->ops.set_vfta = &ixgbe_set_vfta_generic;
251 mac->ops.set_vlvf = &ixgbe_set_vlvf_generic;
252 mac->ops.clear_vfta = &ixgbe_clear_vfta_generic;
253 mac->ops.init_uta_tables = &ixgbe_init_uta_tables_generic;
254 mac->ops.setup_sfp = &ixgbe_setup_sfp_modules_82599;
255 mac->ops.set_mac_anti_spoofing = &ixgbe_set_mac_anti_spoofing;
256 mac->ops.set_vlan_anti_spoofing = &ixgbe_set_vlan_anti_spoofing;
257
258 /* Link */
259 mac->ops.get_link_capabilities = &ixgbe_get_link_capabilities_82599;
260 mac->ops.check_link = &ixgbe_check_mac_link_generic;
261 mac->ops.setup_rxpba = &ixgbe_set_rxpba_generic;
262 ixgbe_init_mac_link_ops_82599(hw);
263
264 mac->mcft_size = 128;
265 mac->vft_size = 128;
266 mac->num_rar_entries = 128;
267 mac->rx_pb_size = 512;
268 mac->max_tx_queues = 128;
269 mac->max_rx_queues = 128;
270 mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw);
271
272 mac->arc_subsystem_valid = (IXGBE_READ_REG(hw, IXGBE_FWSM) &
273 IXGBE_FWSM_MODE_MASK) ? TRUE : FALSE;
274
275 hw->mbx.ops.init_params = ixgbe_init_mbx_params_pf;
276
277 /* EEPROM */
278 eeprom->ops.read = &ixgbe_read_eeprom_82599;
279 eeprom->ops.read_buffer = &ixgbe_read_eeprom_buffer_82599;
280
281 /* Manageability interface */
282 mac->ops.set_fw_drv_ver = &ixgbe_set_fw_drv_ver_generic;
283
284
285 return ret_val;
286 }
287
288 /**
289 * ixgbe_get_link_capabilities_82599 - Determines link capabilities
290 * @hw: pointer to hardware structure
291 * @speed: pointer to link speed
292 * @negotiation: TRUE when autoneg or autotry is enabled
293 *
294 * Determines the link capabilities by reading the AUTOC register.
295 **/
296 s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw,
297 ixgbe_link_speed *speed,
298 bool *negotiation)
299 {
300 s32 status = IXGBE_SUCCESS;
301 u32 autoc = 0;
302
303 DEBUGFUNC("ixgbe_get_link_capabilities_82599");
304
305
306 /* Check if 1G SFP module. */
307 if (hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 ||
308 hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 ||
309 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
310 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
311 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
312 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
313 *speed = IXGBE_LINK_SPEED_1GB_FULL;
314 *negotiation = TRUE;
315 goto out;
316 }
317
318 /*
319 * Determine link capabilities based on the stored value of AUTOC,
320 * which represents EEPROM defaults. If AUTOC value has not
321 * been stored, use the current register values.
322 */
323 if (hw->mac.orig_link_settings_stored)
324 autoc = hw->mac.orig_autoc;
325 else
326 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
327
328 switch (autoc & IXGBE_AUTOC_LMS_MASK) {
329 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
330 *speed = IXGBE_LINK_SPEED_1GB_FULL;
331 *negotiation = FALSE;
332 break;
333
334 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
335 *speed = IXGBE_LINK_SPEED_10GB_FULL;
336 *negotiation = FALSE;
337 break;
338
339 case IXGBE_AUTOC_LMS_1G_AN:
340 *speed = IXGBE_LINK_SPEED_1GB_FULL;
341 *negotiation = TRUE;
342 break;
343
344 case IXGBE_AUTOC_LMS_10G_SERIAL:
345 *speed = IXGBE_LINK_SPEED_10GB_FULL;
346 *negotiation = FALSE;
347 break;
348
349 case IXGBE_AUTOC_LMS_KX4_KX_KR:
350 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
351 *speed = IXGBE_LINK_SPEED_UNKNOWN;
352 if (autoc & IXGBE_AUTOC_KR_SUPP)
353 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
354 if (autoc & IXGBE_AUTOC_KX4_SUPP)
355 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
356 if (autoc & IXGBE_AUTOC_KX_SUPP)
357 *speed |= IXGBE_LINK_SPEED_1GB_FULL;
358 *negotiation = TRUE;
359 break;
360
361 case IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII:
362 *speed = IXGBE_LINK_SPEED_100_FULL;
363 if (autoc & IXGBE_AUTOC_KR_SUPP)
364 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
365 if (autoc & IXGBE_AUTOC_KX4_SUPP)
366 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
367 if (autoc & IXGBE_AUTOC_KX_SUPP)
368 *speed |= IXGBE_LINK_SPEED_1GB_FULL;
369 *negotiation = TRUE;
370 break;
371
372 case IXGBE_AUTOC_LMS_SGMII_1G_100M:
373 *speed = IXGBE_LINK_SPEED_1GB_FULL | IXGBE_LINK_SPEED_100_FULL;
374 *negotiation = FALSE;
375 break;
376
377 default:
378 status = IXGBE_ERR_LINK_SETUP;
379 goto out;
380 }
381
382 if (hw->phy.multispeed_fiber) {
383 *speed |= IXGBE_LINK_SPEED_10GB_FULL |
384 IXGBE_LINK_SPEED_1GB_FULL;
385 *negotiation = TRUE;
386 }
387
388 out:
389 return status;
390 }
391
392 /**
393 * ixgbe_get_media_type_82599 - Get media type
394 * @hw: pointer to hardware structure
395 *
396 * Returns the media type (fiber, copper, backplane)
397 **/
398 enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw)
399 {
400 enum ixgbe_media_type media_type;
401
402 DEBUGFUNC("ixgbe_get_media_type_82599");
403
404 /* Detect if there is a copper PHY attached. */
405 switch (hw->phy.type) {
408 media_type = ixgbe_media_type_copper;
409 goto out;
410 default:
411 break;
412 }
413
414 switch (hw->device_id) {
415 case IXGBE_DEV_ID_82599_KX4:
416 case IXGBE_DEV_ID_82599_KX4_MEZZ:
417 case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
418 case IXGBE_DEV_ID_82599_KR:
419 case IXGBE_DEV_ID_82599_BACKPLANE_FCOE:
420 case IXGBE_DEV_ID_82599_XAUI_LOM:
421 /* Default device ID is mezzanine card KX/KX4 */
422 media_type = ixgbe_media_type_backplane;
423 break;
424 case IXGBE_DEV_ID_82599_SFP:
425 case IXGBE_DEV_ID_82599_SFP_FCOE:
426 case IXGBE_DEV_ID_82599_SFP_EM:
427 case IXGBE_DEV_ID_82599_SFP_SF2:
428 case IXGBE_DEV_ID_82599EN_SFP:
429 media_type = ixgbe_media_type_fiber;
430 break;
431 case IXGBE_DEV_ID_82599_CX4:
432 media_type = ixgbe_media_type_cx4;
433 break;
434 case IXGBE_DEV_ID_82599_T3_LOM:
435 media_type = ixgbe_media_type_copper;
436 break;
437 default:
438 media_type = ixgbe_media_type_unknown;
439 break;
440 }
441 out:
442 return media_type;
443 }
444
445 /**
446 * ixgbe_start_mac_link_82599 - Setup MAC link settings
447 * @hw: pointer to hardware structure
448 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
449 *
450 * Configures link settings based on values in the ixgbe_hw struct.
451 * Restarts the link. Performs autonegotiation if needed.
452 **/
453 s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw,
454 bool autoneg_wait_to_complete)
455 {
456 u32 autoc_reg;
457 u32 links_reg;
458 u32 i;
459 s32 status = IXGBE_SUCCESS;
460
461 DEBUGFUNC("ixgbe_start_mac_link_82599");
462
463
464 /* Restart link */
465 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
466 autoc_reg |= IXGBE_AUTOC_AN_RESTART;
467 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
468
469 /* Only poll for autoneg to complete if specified to do so */
470 if (autoneg_wait_to_complete) {
471 if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
472 IXGBE_AUTOC_LMS_KX4_KX_KR ||
473 (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
474 IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
475 (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
476 IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
477 links_reg = 0; /* Just in case Autoneg time = 0 */
478 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
479 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
480 if (links_reg & IXGBE_LINKS_KX_AN_COMP)
481 break;
482 msec_delay(100);
483 }
484 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
485 status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
486 DEBUGOUT("Autoneg did not complete.\n");
487 }
488 }
489 }
490
491 /* Add delay to filter out noises during initial link setup */
492 msec_delay(50);
493
494 return status;
495 }
496
497 /**
498 * ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
499 * @hw: pointer to hardware structure
500 *
501 * The base drivers may require better control over SFP+ module
502 * PHY states. This includes selectively shutting down the Tx
503 * laser on the PHY, effectively halting physical link.
504 **/
505 void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
506 {
507 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
508
509 /* Disable tx laser; allow 100us to go dark per spec */
510 esdp_reg |= IXGBE_ESDP_SDP3;
511 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
512 IXGBE_WRITE_FLUSH(hw);
513 usec_delay(100);
514 }
515
516 /**
517 * ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
518 * @hw: pointer to hardware structure
519 *
520 * The base drivers may require better control over SFP+ module
521 * PHY states. This includes selectively turning on the Tx
522 * laser on the PHY, effectively starting physical link.
523 **/
524 void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
525 {
526 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
527
528 /* Enable tx laser; allow 100ms to light up */
529 esdp_reg &= ~IXGBE_ESDP_SDP3;
530 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
531 IXGBE_WRITE_FLUSH(hw);
532 msec_delay(100);
533 }
534
535 /**
536 * ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
537 * @hw: pointer to hardware structure
538 *
539 * When the driver changes the link speeds that it can support,
540 * it sets autotry_restart to TRUE to indicate that we need to
541 * initiate a new autotry session with the link partner. To do
542 * so, we set the speed then disable and re-enable the tx laser, to
543 * alert the link partner that it also needs to restart autotry on its
544 * end. This is consistent with TRUE clause 37 autoneg, which also
545 * involves a loss of signal.
546 **/
547 void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
548 {
549 DEBUGFUNC("ixgbe_flap_tx_laser_multispeed_fiber");
550
551 if (hw->mac.autotry_restart) {
552 ixgbe_disable_tx_laser_multispeed_fiber(hw);
553 ixgbe_enable_tx_laser_multispeed_fiber(hw);
554 hw->mac.autotry_restart = FALSE;
555 }
556 }
557
558 /**
559 * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
560 * @hw: pointer to hardware structure
561 * @speed: new link speed
562 * @autoneg: TRUE if autonegotiation enabled
563 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
564 *
565 * Set the link speed in the AUTOC register and restarts link.
566 **/
567 s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
568 ixgbe_link_speed speed, bool autoneg,
569 bool autoneg_wait_to_complete)
570 {
571 s32 status = IXGBE_SUCCESS;
572 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
573 ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
574 u32 speedcnt = 0;
575 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
576 u32 i = 0;
577 bool link_up = FALSE;
578 bool negotiation;
579
580 DEBUGFUNC("ixgbe_setup_mac_link_multispeed_fiber");
581
582 /* Mask off requested but non-supported speeds */
583 status = ixgbe_get_link_capabilities(hw, &link_speed, &negotiation);
584 if (status != IXGBE_SUCCESS)
585 return status;
586
587 speed &= link_speed;
588
589 /*
590 * Try each speed one by one, highest priority first. We do this in
591 * software because 10gb fiber doesn't support speed autonegotiation.
592 */
593 if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
594 speedcnt++;
595 highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
596
597 /* If we already have link at this speed, just jump out */
598 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE);
599 if (status != IXGBE_SUCCESS)
600 return status;
601
602 if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
603 goto out;
604
605 /* Set the module link speed */
606 esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
607 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
608 IXGBE_WRITE_FLUSH(hw);
609
610 /* Allow module to change analog characteristics (1G->10G) */
611 msec_delay(40);
612
613 status = ixgbe_setup_mac_link_82599(hw,
614 IXGBE_LINK_SPEED_10GB_FULL,
615 autoneg,
616 autoneg_wait_to_complete);
617 if (status != IXGBE_SUCCESS)
618 return status;
619
620 /* Flap the tx laser if it has not already been done */
621 ixgbe_flap_tx_laser(hw);
622
623 /*
624 * Wait for the controller to acquire link. Per IEEE 802.3ap,
625 * Section 73.10.2, we may have to wait up to 500ms if KR is
626 * attempted. 82599 uses the same timing for 10g SFI.
627 */
628 for (i = 0; i < 5; i++) {
629 /* Wait for the link partner to also set speed */
630 msec_delay(100);
631
632 /* If we have link, just jump out */
633 status = ixgbe_check_link(hw, &link_speed,
634 &link_up, FALSE);
635 if (status != IXGBE_SUCCESS)
636 return status;
637
638 if (link_up)
639 goto out;
640 }
641 }
642
643 if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
644 speedcnt++;
645 if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
646 highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
647
648 /* If we already have link at this speed, just jump out */
649 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE);
650 if (status != IXGBE_SUCCESS)
651 return status;
652
653 if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
654 goto out;
655
656 /* Set the module link speed */
657 esdp_reg &= ~IXGBE_ESDP_SDP5;
658 esdp_reg |= IXGBE_ESDP_SDP5_DIR;
659 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
660 IXGBE_WRITE_FLUSH(hw);
661
662 /* Allow module to change analog characteristics (10G->1G) */
663 msec_delay(40);
664
665 status = ixgbe_setup_mac_link_82599(hw,
666 IXGBE_LINK_SPEED_1GB_FULL,
667 autoneg,
668 autoneg_wait_to_complete);
669 if (status != IXGBE_SUCCESS)
670 return status;
671
672 /* Flap the tx laser if it has not already been done */
673 ixgbe_flap_tx_laser(hw);
674
675 /* Wait for the link partner to also set speed */
676 msec_delay(100);
677
678 /* If we have link, just jump out */
679 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE);
680 if (status != IXGBE_SUCCESS)
681 return status;
682
683 if (link_up)
684 goto out;
685 }
686
687 /*
688 * We didn't get link. Configure back to the highest speed we tried,
689 * (if there was more than one). We call ourselves back with just the
690 * single highest speed that the user requested.
691 */
692 if (speedcnt > 1)
693 status = ixgbe_setup_mac_link_multispeed_fiber(hw,
694 highest_link_speed, autoneg, autoneg_wait_to_complete);
695
696 out:
697 /* Set autoneg_advertised value based on input link speed */
698 hw->phy.autoneg_advertised = 0;
699
700 if (speed & IXGBE_LINK_SPEED_10GB_FULL)
701 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
702
703 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
704 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
705
706 return status;
707 }
708
709 /**
710 * ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed
711 * @hw: pointer to hardware structure
712 * @speed: new link speed
713 * @autoneg: TRUE if autonegotiation enabled
714 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
715 *
716 * Implements the Intel SmartSpeed algorithm.
717 **/
718 s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
719 ixgbe_link_speed speed, bool autoneg,
720 bool autoneg_wait_to_complete)
721 {
722 s32 status = IXGBE_SUCCESS;
723 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
724 s32 i, j;
725 bool link_up = FALSE;
726 u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
727
728 DEBUGFUNC("ixgbe_setup_mac_link_smartspeed");
729
730 /* Set autoneg_advertised value based on input link speed */
731 hw->phy.autoneg_advertised = 0;
732
733 if (speed & IXGBE_LINK_SPEED_10GB_FULL)
734 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
735
736 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
737 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
738
739 if (speed & IXGBE_LINK_SPEED_100_FULL)
740 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL;
741
742 /*
743 * Implement Intel SmartSpeed algorithm. SmartSpeed will reduce the
744 * autoneg advertisement if link is unable to be established at the
745 * highest negotiated rate. This can sometimes happen due to integrity
746 * issues with the physical media connection.
747 */
748
749 /* First, try to get link with full advertisement */
750 hw->phy.smart_speed_active = FALSE;
751 for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) {
752 status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
753 autoneg_wait_to_complete);
754 if (status != IXGBE_SUCCESS)
755 goto out;
756
757 /*
758 * Wait for the controller to acquire link. Per IEEE 802.3ap,
759 * Section 73.10.2, we may have to wait up to 500ms if KR is
760 * attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per
761 * Table 9 in the AN MAS.
762 */
763 for (i = 0; i < 5; i++) {
764 msec_delay(100);
765
766 /* If we have link, just jump out */
767 status = ixgbe_check_link(hw, &link_speed, &link_up,
768 FALSE);
769 if (status != IXGBE_SUCCESS)
770 goto out;
771
772 if (link_up)
773 goto out;
774 }
775 }
776
777 /*
778 * We didn't get link. If we advertised KR plus one of KX4/KX
779 * (or BX4/BX), then disable KR and try again.
780 */
781 if (((autoc_reg & IXGBE_AUTOC_KR_SUPP) == 0) ||
782 ((autoc_reg & IXGBE_AUTOC_KX4_KX_SUPP_MASK) == 0))
783 goto out;
784
785 /* Turn SmartSpeed on to disable KR support */
786 hw->phy.smart_speed_active = TRUE;
787 status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
788 autoneg_wait_to_complete);
789 if (status != IXGBE_SUCCESS)
790 goto out;
791
792 /*
793 * Wait for the controller to acquire link. 600ms will allow for
794 * the AN link_fail_inhibit_timer as well for multiple cycles of
795 * parallel detect, both 10g and 1g. This allows for the maximum
796 * connect attempts as defined in the AN MAS table 73-7.
797 */
798 for (i = 0; i < 6; i++) {
799 msec_delay(100);
800
801 /* If we have link, just jump out */
802 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE);
803 if (status != IXGBE_SUCCESS)
804 goto out;
805
806 if (link_up)
807 goto out;
808 }
809
810 /* We didn't get link. Turn SmartSpeed back off. */
811 hw->phy.smart_speed_active = FALSE;
812 status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
813 autoneg_wait_to_complete);
814
815 out:
816 if (link_up && (link_speed == IXGBE_LINK_SPEED_1GB_FULL))
817 DEBUGOUT("Smartspeed has downgraded the link speed "
818 "from the maximum advertised\n");
819 return status;
820 }
821
822 /**
823 * ixgbe_setup_mac_link_82599 - Set MAC link speed
824 * @hw: pointer to hardware structure
825 * @speed: new link speed
826 * @autoneg: TRUE if autonegotiation enabled
827 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
828 *
829 * Set the link speed in the AUTOC register and restarts link.
830 **/
831 s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
832 ixgbe_link_speed speed, bool autoneg,
833 bool autoneg_wait_to_complete)
834 {
835 s32 status = IXGBE_SUCCESS;
836 u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
837 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
838 u32 start_autoc = autoc;
839 u32 orig_autoc = 0;
840 u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
841 u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
842 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
843 u32 links_reg;
844 u32 i;
845 ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN;
846
847 DEBUGFUNC("ixgbe_setup_mac_link_82599");
848
849 /* Check to see if speed passed in is supported. */
850 status = ixgbe_get_link_capabilities(hw, &link_capabilities, &autoneg);
851 if (status != IXGBE_SUCCESS)
852 goto out;
853
854 speed &= link_capabilities;
855
856 if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
857 status = IXGBE_ERR_LINK_SETUP;
858 goto out;
859 }
860
861 /* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/
862 if (hw->mac.orig_link_settings_stored)
863 orig_autoc = hw->mac.orig_autoc;
864 else
865 orig_autoc = autoc;
866
867 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
868 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
869 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
870 /* Set KX4/KX/KR support according to speed requested */
871 autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP);
872 if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
873 if (orig_autoc & IXGBE_AUTOC_KX4_SUPP)
874 autoc |= IXGBE_AUTOC_KX4_SUPP;
875 if ((orig_autoc & IXGBE_AUTOC_KR_SUPP) &&
876 (hw->phy.smart_speed_active == FALSE))
877 autoc |= IXGBE_AUTOC_KR_SUPP;
878 }
879 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
880 autoc |= IXGBE_AUTOC_KX_SUPP;
881 } else if ((pma_pmd_1g == IXGBE_AUTOC_1G_SFI) &&
882 (link_mode == IXGBE_AUTOC_LMS_1G_LINK_NO_AN ||
883 link_mode == IXGBE_AUTOC_LMS_1G_AN)) {
884 /* Switch from 1G SFI to 10G SFI if requested */
885 if ((speed == IXGBE_LINK_SPEED_10GB_FULL) &&
886 (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)) {
887 autoc &= ~IXGBE_AUTOC_LMS_MASK;
888 autoc |= IXGBE_AUTOC_LMS_10G_SERIAL;
889 }
890 } else if ((pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) &&
891 (link_mode == IXGBE_AUTOC_LMS_10G_SERIAL)) {
892 /* Switch from 10G SFI to 1G SFI if requested */
893 if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
894 (pma_pmd_1g == IXGBE_AUTOC_1G_SFI)) {
895 autoc &= ~IXGBE_AUTOC_LMS_MASK;
896 if (autoneg)
897 autoc |= IXGBE_AUTOC_LMS_1G_AN;
898 else
899 autoc |= IXGBE_AUTOC_LMS_1G_LINK_NO_AN;
900 }
901 }
902
903 if (autoc != start_autoc) {
904 /* Restart link */
905 autoc |= IXGBE_AUTOC_AN_RESTART;
906 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
907
908 /* Only poll for autoneg to complete if specified to do so */
909 if (autoneg_wait_to_complete) {
910 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
911 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
912 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
913 links_reg = 0; /*Just in case Autoneg time=0*/
914 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
915 links_reg =
916 IXGBE_READ_REG(hw, IXGBE_LINKS);
917 if (links_reg & IXGBE_LINKS_KX_AN_COMP)
918 break;
919 msec_delay(100);
920 }
921 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
922 status =
923 IXGBE_ERR_AUTONEG_NOT_COMPLETE;
924 DEBUGOUT("Autoneg did not complete.\n");
925 }
926 }
927 }
928
929 /* Add delay to filter out noises during initial link setup */
930 msec_delay(50);
931 }
932
933 out:
934 return status;
935 }
936
937 /**
938 * ixgbe_setup_copper_link_82599 - Set the PHY autoneg advertised field
939 * @hw: pointer to hardware structure
940 * @speed: new link speed
941 * @autoneg: TRUE if autonegotiation enabled
942 * @autoneg_wait_to_complete: TRUE if waiting is needed to complete
943 *
944 * Restarts link on PHY and MAC based on settings passed in.
945 **/
946 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
947 ixgbe_link_speed speed,
948 bool autoneg,
949 bool autoneg_wait_to_complete)
950 {
951 s32 status;
952
953 DEBUGFUNC("ixgbe_setup_copper_link_82599");
954
955 /* Setup the PHY according to input speed */
956 status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
957 autoneg_wait_to_complete);
958 if (status == IXGBE_SUCCESS) {
959 /* Set up MAC */
960 status =
961 ixgbe_start_mac_link_82599(hw, autoneg_wait_to_complete);
962 }
963
964 return status;
965 }
966
967 /**
968 * ixgbe_reset_hw_82599 - Perform hardware reset
969 * @hw: pointer to hardware structure
970 *
971 * Resets the hardware by resetting the transmit and receive units, masks
972 * and clears all interrupts, perform a PHY reset, and perform a link (MAC)
973 * reset.
974 **/
975 s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
976 {
977 ixgbe_link_speed link_speed;
978 s32 status;
979 u32 ctrl, i, autoc, autoc2;
980 bool link_up = FALSE;
981
982 DEBUGFUNC("ixgbe_reset_hw_82599");
983
984 /* Call adapter stop to disable tx/rx and clear interrupts */
985 status = hw->mac.ops.stop_adapter(hw);
986 if (status != IXGBE_SUCCESS)
987 goto reset_hw_out;
988
989 /* flush pending Tx transactions */
990 ixgbe_clear_tx_pending(hw);
991
992 /* PHY ops must be identified and initialized prior to reset */
993
994 /* Identify PHY and related function pointers */
995 status = hw->phy.ops.init(hw);
996
997 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
998 goto reset_hw_out;
999
1000 /* Setup SFP module if there is one present. */
1001 if (hw->phy.sfp_setup_needed) {
1002 status = hw->mac.ops.setup_sfp(hw);
1003 hw->phy.sfp_setup_needed = FALSE;
1004 }
1005
1006 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
1007 goto reset_hw_out;
1008
1009 /* Reset PHY */
1010 if (hw->phy.reset_disable == FALSE && hw->phy.ops.reset != NULL)
1011 hw->phy.ops.reset(hw);
1012
1013 mac_reset_top:
1014 /*
1015 * Issue global reset to the MAC. Needs to be SW reset if link is up.
1016 * If link reset is used when link is up, it might reset the PHY when
1017 * mng is using it. If link is down or the flag to force full link
1018 * reset is set, then perform link reset.
1019 */
1020 ctrl = IXGBE_CTRL_LNK_RST;
1021 if (!hw->force_full_reset) {
1022 hw->mac.ops.check_link(hw, &link_speed, &link_up, FALSE);
1023 if (link_up)
1024 ctrl = IXGBE_CTRL_RST;
1025 }
1026
1027 ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
1028 IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl);
1029 IXGBE_WRITE_FLUSH(hw);
1030
1031 /* Poll for reset bit to self-clear indicating reset is complete */
1032 for (i = 0; i < 10; i++) {
1033 usec_delay(1);
1034 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
1035 if (!(ctrl & IXGBE_CTRL_RST_MASK))
1036 break;
1037 }
1038
1039 if (ctrl & IXGBE_CTRL_RST_MASK) {
1040 status = IXGBE_ERR_RESET_FAILED;
1041 DEBUGOUT("Reset polling failed to complete.\n");
1042 }
1043
1044 msec_delay(50);
1045
1046 /*
1047 * Double resets are required for recovery from certain error
1048 * conditions. Between resets, it is necessary to stall to allow time
1049 * for any pending HW events to complete.
1050 */
1051 if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) {
1052 hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
1053 goto mac_reset_top;
1054 }
1055
1056 /*
1057 * Store the original AUTOC/AUTOC2 values if they have not been
1058 * stored off yet. Otherwise restore the stored original
1059 * values since the reset operation sets back to defaults.
1060 */
1061 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
1062 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
1063 if (hw->mac.orig_link_settings_stored == FALSE) {
1064 hw->mac.orig_autoc = autoc;
1065 hw->mac.orig_autoc2 = autoc2;
1066 hw->mac.orig_link_settings_stored = TRUE;
1067 } else {
1068 if (autoc != hw->mac.orig_autoc)
1069 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, (hw->mac.orig_autoc |
1070 IXGBE_AUTOC_AN_RESTART));
1071
1072 if ((autoc2 & IXGBE_AUTOC2_UPPER_MASK) !=
1073 (hw->mac.orig_autoc2 & IXGBE_AUTOC2_UPPER_MASK)) {
1074 autoc2 &= ~IXGBE_AUTOC2_UPPER_MASK;
1075 autoc2 |= (hw->mac.orig_autoc2 &
1076 IXGBE_AUTOC2_UPPER_MASK);
1077 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2);
1078 }
1079 }
1080
1081 /* Store the permanent mac address */
1082 hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
1083
1084 /*
1085 * Store MAC address from RAR0, clear receive address registers, and
1086 * clear the multicast table. Also reset num_rar_entries to 128,
1087 * since we modify this value when programming the SAN MAC address.
1088 */
1089 hw->mac.num_rar_entries = 128;
1090 hw->mac.ops.init_rx_addrs(hw);
1091
1096 if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
1097 hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
1098 hw->mac.san_addr, 0, IXGBE_RAH_AV);
1099
1100 /* Save the SAN MAC RAR index */
1101 hw->mac.san_mac_rar_index = hw->mac.num_rar_entries - 1;
1102
1103 /* Reserve the last RAR for the SAN MAC address */
1104 hw->mac.num_rar_entries--;
1105 }
1106
1107 /* Store the alternative WWNN/WWPN prefix */
1108 hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix,
1109 &hw->mac.wwpn_prefix);
1110
1111 reset_hw_out:
1112 return status;
1113 }
1114
1115 /**
1116 * ixgbe_reinit_fdir_tables_82599 - Reinitialize Flow Director tables.
1117 * @hw: pointer to hardware structure
1118 **/
1119 s32 ixgbe_reinit_fdir_tables_82599(struct ixgbe_hw *hw)
1120 {
1121 int i;
1122 u32 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL);
1123 fdirctrl &= ~IXGBE_FDIRCTRL_INIT_DONE;
1124
1125 DEBUGFUNC("ixgbe_reinit_fdir_tables_82599");
1126
1127 /*
1128 * Before starting reinitialization process,
1129 * FDIRCMD.CMD must be zero.
1130 */
1131 for (i = 0; i < IXGBE_FDIRCMD_CMD_POLL; i++) {
1132 if (!(IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
1133 IXGBE_FDIRCMD_CMD_MASK))
1134 break;
1135 usec_delay(10);
1136 }
1137 if (i >= IXGBE_FDIRCMD_CMD_POLL) {
1138 DEBUGOUT("Flow Director previous command isn't complete, "
1139 "aborting table re-initialization.\n");
1140 return IXGBE_ERR_FDIR_REINIT_FAILED;
1141 }
1142
1143 IXGBE_WRITE_REG(hw, IXGBE_FDIRFREE, 0);
1144 IXGBE_WRITE_FLUSH(hw);
1145 /*
1146 * 82599 adapters flow director init flow cannot be restarted,
1147 * Workaround 82599 silicon errata by performing the following steps
1148 * before re-writing the FDIRCTRL control register with the same value.
1149 * - write 1 to bit 8 of FDIRCMD register &
1150 * - write 0 to bit 8 of FDIRCMD register
1151 */
1152 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1153 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) |
1154 IXGBE_FDIRCMD_CLEARHT));
1155 IXGBE_WRITE_FLUSH(hw);
1156 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1157 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
1158 ~IXGBE_FDIRCMD_CLEARHT));
1159 IXGBE_WRITE_FLUSH(hw);
1160 /*
1161 * Clear FDIR Hash register to clear any leftover hashes
1162 * waiting to be programmed.
1163 */
1164 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, 0x00);
1165 IXGBE_WRITE_FLUSH(hw);
1166
1167 IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl);
1168 IXGBE_WRITE_FLUSH(hw);
1169
1170 /* Poll init-done after we write FDIRCTRL register */
1171 for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) {
1172 if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) &
1173 IXGBE_FDIRCTRL_INIT_DONE)
1174 break;
1175 usec_delay(10);
1176 }
1177 if (i >= IXGBE_FDIR_INIT_DONE_POLL) {
1178 DEBUGOUT("Flow Director Signature poll time exceeded!\n");
1179 return IXGBE_ERR_FDIR_REINIT_FAILED;
1180 }
1181
1182 /* Clear FDIR statistics registers (read to clear) */
1183 (void) IXGBE_READ_REG(hw, IXGBE_FDIRUSTAT);
1184 (void) IXGBE_READ_REG(hw, IXGBE_FDIRFSTAT);
1185 (void) IXGBE_READ_REG(hw, IXGBE_FDIRMATCH);
1186 (void) IXGBE_READ_REG(hw, IXGBE_FDIRMISS);
1187 (void) IXGBE_READ_REG(hw, IXGBE_FDIRLEN);
1188
1189 return IXGBE_SUCCESS;
1190 }
1191
1192 /**
1193 * ixgbe_fdir_enable_82599 - Initialize Flow Director control registers
1194 * @hw: pointer to hardware structure
1195 * @fdirctrl: value to write to flow director control register
1196 **/
1197 static void ixgbe_fdir_enable_82599(struct ixgbe_hw *hw, u32 fdirctrl)
1198 {
1199 int i;
1200
1201 DEBUGFUNC("ixgbe_fdir_enable_82599");
1202
1203 /* Prime the keys for hashing */
1204 IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY, IXGBE_ATR_BUCKET_HASH_KEY);
1205 IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY, IXGBE_ATR_SIGNATURE_HASH_KEY);
1206
1207 /*
1244 * Continue setup of fdirctrl register bits:
1245 * Move the flexible bytes to use the ethertype - shift 6 words
1246 * Set the maximum length per hash bucket to 0xA filters
1247 * Send interrupt when 64 filters are left
1248 */
1249 fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) |
1250 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) |
1251 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT);
1252
1253 /* write hashes and fdirctrl register, poll for completion */
1254 ixgbe_fdir_enable_82599(hw, fdirctrl);
1255
1256 return IXGBE_SUCCESS;
1257 }
1258
1259 /**
1260 * ixgbe_init_fdir_perfect_82599 - Initialize Flow Director perfect filters
1261 * @hw: pointer to hardware structure
1262 * @fdirctrl: value to write to flow director control register, initially
1263 * contains just the value of the Rx packet buffer allocation
1264 **/
1265 s32 ixgbe_init_fdir_perfect_82599(struct ixgbe_hw *hw, u32 fdirctrl)
1266 {
1267 DEBUGFUNC("ixgbe_init_fdir_perfect_82599");
1268
1269 /*
1270 * Continue setup of fdirctrl register bits:
1271 * Turn perfect match filtering on
1272 * Report hash in RSS field of Rx wb descriptor
1273 * Initialize the drop queue
1274 * Move the flexible bytes to use the ethertype - shift 6 words
1275 * Set the maximum length per hash bucket to 0xA filters
1276 * Send interrupt when 64 (0x4 * 16) filters are left
1277 */
1278 fdirctrl |= IXGBE_FDIRCTRL_PERFECT_MATCH |
1279 IXGBE_FDIRCTRL_REPORT_STATUS |
1280 (IXGBE_FDIR_DROP_QUEUE << IXGBE_FDIRCTRL_DROP_Q_SHIFT) |
1281 (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) |
1282 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) |
1283 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT);
1284
1285 /* write hashes and fdirctrl register, poll for completion */
1286 ixgbe_fdir_enable_82599(hw, fdirctrl);
1287
1288 return IXGBE_SUCCESS;
1289 }
1290
1291 /*
1292 * These defines allow us to quickly generate all of the necessary instructions
1293 * in the function below by simply calling out IXGBE_COMPUTE_SIG_HASH_ITERATION
1294 * for values 0 through 15
1295 */
1296 #define IXGBE_ATR_COMMON_HASH_KEY \
1297 (IXGBE_ATR_BUCKET_HASH_KEY & IXGBE_ATR_SIGNATURE_HASH_KEY)
1298 #ifdef lint
1299 #define IXGBE_COMPUTE_SIG_HASH_ITERATION(_n)
1300 #else
1301 #define IXGBE_COMPUTE_SIG_HASH_ITERATION(_n) \
1302 do { \
1303 u32 n = (_n); \
1304 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << n)) \
1305 common_hash ^= lo_hash_dword >> n; \
1306 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \
1307 bucket_hash ^= lo_hash_dword >> n; \
1308 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << n)) \
1309 sig_hash ^= lo_hash_dword << (16 - n); \
1310 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << (n + 16))) \
1311 common_hash ^= hi_hash_dword >> n; \
1312 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \
1313 bucket_hash ^= hi_hash_dword >> n; \
1314 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << (n + 16))) \
1315 sig_hash ^= hi_hash_dword << (16 - n); \
1316 } while (0);
1317 #endif
1318
1319 /**
1320 * ixgbe_atr_compute_sig_hash_82599 - Compute the signature hash
1321 * @stream: input bitstream to compute the hash on
1322 *
1323 * This function is almost identical to the function above but contains
1324 * several optomizations such as unwinding all of the loops, letting the
1325 * compiler work out all of the conditional ifs since the keys are static
1326 * defines, and computing two keys at once since the hashed dword stream
1327 * will be the same for both keys.
1328 **/
1329 u32 ixgbe_atr_compute_sig_hash_82599(union ixgbe_atr_hash_dword input,
1330 union ixgbe_atr_hash_dword common)
1331 {
1332 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan;
1333 u32 sig_hash = 0, bucket_hash = 0, common_hash = 0;
1334
1335 /* record the flow_vm_vlan bits as they are a key part to the hash */
1336 flow_vm_vlan = IXGBE_NTOHL(input.dword);
1337
1338 /* generate common hash dword */
1339 hi_hash_dword = IXGBE_NTOHL(common.dword);
1340
1341 /* low dword is word swapped version of common */
1342 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16);
1343
1344 /* apply flow ID/VM pool/VLAN ID bits to hash words */
1345 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16);
1346
1347 /* Process bits 0 and 16 */
1348 IXGBE_COMPUTE_SIG_HASH_ITERATION(0);
1349
1350 /*
1351 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to
1352 * delay this because bit 0 of the stream should not be processed
1353 * so we do not add the vlan until after bit 0 was processed
1354 */
1355 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16);
1356
1357 /* Process remaining 30 bit of the key */
1358 IXGBE_COMPUTE_SIG_HASH_ITERATION(1);
1359 IXGBE_COMPUTE_SIG_HASH_ITERATION(2);
1360 IXGBE_COMPUTE_SIG_HASH_ITERATION(3);
1361 IXGBE_COMPUTE_SIG_HASH_ITERATION(4);
1362 IXGBE_COMPUTE_SIG_HASH_ITERATION(5);
1363 IXGBE_COMPUTE_SIG_HASH_ITERATION(6);
1364 IXGBE_COMPUTE_SIG_HASH_ITERATION(7);
1365 IXGBE_COMPUTE_SIG_HASH_ITERATION(8);
1366 IXGBE_COMPUTE_SIG_HASH_ITERATION(9);
1367 IXGBE_COMPUTE_SIG_HASH_ITERATION(10);
1368 IXGBE_COMPUTE_SIG_HASH_ITERATION(11);
1369 IXGBE_COMPUTE_SIG_HASH_ITERATION(12);
1370 IXGBE_COMPUTE_SIG_HASH_ITERATION(13);
1371 IXGBE_COMPUTE_SIG_HASH_ITERATION(14);
1372 IXGBE_COMPUTE_SIG_HASH_ITERATION(15);
1373
1374 /* combine common_hash result with signature and bucket hashes */
1375 bucket_hash ^= common_hash;
1376 bucket_hash &= IXGBE_ATR_HASH_MASK;
1377
1378 sig_hash ^= common_hash << 16;
1379 sig_hash &= IXGBE_ATR_HASH_MASK << 16;
1380
1381 /* return completed signature hash */
1382 return sig_hash ^ bucket_hash;
1383 }
1384
1385 /**
1386 * ixgbe_atr_add_signature_filter_82599 - Adds a signature hash filter
1387 * @hw: pointer to hardware structure
1388 * @input: unique input dword
1389 * @common: compressed common input dword
1390 * @queue: queue index to direct traffic to
1391 **/
1392 s32 ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw,
1393 union ixgbe_atr_hash_dword input,
1394 union ixgbe_atr_hash_dword common,
1395 u8 queue)
1396 {
1397 u64 fdirhashcmd;
1398 u32 fdircmd;
1399
1400 DEBUGFUNC("ixgbe_fdir_add_signature_filter_82599");
1401
1402 /*
1403 * Get the flow_type in order to program FDIRCMD properly
1404 * lowest 2 bits are FDIRCMD.L4TYPE, third lowest bit is FDIRCMD.IPV6
1405 */
1406 switch (input.formatted.flow_type) {
1407 case IXGBE_ATR_FLOW_TYPE_TCPV4:
1408 case IXGBE_ATR_FLOW_TYPE_UDPV4:
1409 case IXGBE_ATR_FLOW_TYPE_SCTPV4:
1410 case IXGBE_ATR_FLOW_TYPE_TCPV6:
1411 case IXGBE_ATR_FLOW_TYPE_UDPV6:
1412 case IXGBE_ATR_FLOW_TYPE_SCTPV6:
1413 break;
1414 default:
1415 DEBUGOUT(" Error on flow type input\n");
1416 return IXGBE_ERR_CONFIG;
1417 }
1418
1419 /* configure FDIRCMD register */
1420 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE |
1421 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN;
1422 fdircmd |= input.formatted.flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT;
1423 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT;
1424
1425 /*
1426 * The lower 32-bits of fdirhashcmd is for FDIRHASH, the upper 32-bits
1427 * is for FDIRCMD. Then do a 64-bit register write from FDIRHASH.
1428 */
1429 fdirhashcmd = (u64)fdircmd << 32;
1430 fdirhashcmd |= ixgbe_atr_compute_sig_hash_82599(input, common);
1431 IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd);
1432
1433 DEBUGOUT2("Tx Queue=%x hash=%x\n", queue, (u32)fdirhashcmd);
1434
1435 return IXGBE_SUCCESS;
1436 }
1437
1438 #ifdef lint
1439 #define IXGBE_COMPUTE_BKT_HASH_ITERATION(_n)
1440 #else
1441 #define IXGBE_COMPUTE_BKT_HASH_ITERATION(_n) \
1442 do { \
1443 u32 n = (_n); \
1444 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \
1445 bucket_hash ^= lo_hash_dword >> n; \
1446 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \
1447 bucket_hash ^= hi_hash_dword >> n; \
1448 } while (0);
1449 #endif
1450 /**
1451 * ixgbe_atr_compute_perfect_hash_82599 - Compute the perfect filter hash
1452 * @atr_input: input bitstream to compute the hash on
1453 * @input_mask: mask for the input bitstream
1454 *
1455 * This function serves two main purposes. First it applys the input_mask
1456 * to the atr_input resulting in a cleaned up atr_input data stream.
1457 * Secondly it computes the hash and stores it in the bkt_hash field at
1458 * the end of the input byte stream. This way it will be available for
1459 * future use without needing to recompute the hash.
1460 **/
1461 void ixgbe_atr_compute_perfect_hash_82599(union ixgbe_atr_input *input,
1462 union ixgbe_atr_input *input_mask)
1463 {
1464
1465 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan;
1466 u32 bucket_hash = 0;
1467
1468 /* Apply masks to input data */
1469 input->dword_stream[0] &= input_mask->dword_stream[0];
1470 input->dword_stream[1] &= input_mask->dword_stream[1];
1471 input->dword_stream[2] &= input_mask->dword_stream[2];
1472 input->dword_stream[3] &= input_mask->dword_stream[3];
1473 input->dword_stream[4] &= input_mask->dword_stream[4];
1474 input->dword_stream[5] &= input_mask->dword_stream[5];
1475 input->dword_stream[6] &= input_mask->dword_stream[6];
1476 input->dword_stream[7] &= input_mask->dword_stream[7];
1477 input->dword_stream[8] &= input_mask->dword_stream[8];
1478 input->dword_stream[9] &= input_mask->dword_stream[9];
1479 input->dword_stream[10] &= input_mask->dword_stream[10];
1480
1481 /* record the flow_vm_vlan bits as they are a key part to the hash */
1482 flow_vm_vlan = IXGBE_NTOHL(input->dword_stream[0]);
1483
1484 /* generate common hash dword */
1485 hi_hash_dword = IXGBE_NTOHL(input->dword_stream[1] ^
1486 input->dword_stream[2] ^
1487 input->dword_stream[3] ^
1488 input->dword_stream[4] ^
1489 input->dword_stream[5] ^
1490 input->dword_stream[6] ^
1491 input->dword_stream[7] ^
1492 input->dword_stream[8] ^
1493 input->dword_stream[9] ^
1494 input->dword_stream[10]);
1495
1496 /* low dword is word swapped version of common */
1497 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16);
1498
1499 /* apply flow ID/VM pool/VLAN ID bits to hash words */
1500 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16);
1501
1502 /* Process bits 0 and 16 */
1503 IXGBE_COMPUTE_BKT_HASH_ITERATION(0);
1504
1505 /*
1506 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to
1507 * delay this because bit 0 of the stream should not be processed
1508 * so we do not add the vlan until after bit 0 was processed
1509 */
1510 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16);
1511
1512 /* Process remaining 30 bit of the key */
1513 IXGBE_COMPUTE_BKT_HASH_ITERATION(1);
1514 IXGBE_COMPUTE_BKT_HASH_ITERATION(2);
1515 IXGBE_COMPUTE_BKT_HASH_ITERATION(3);
1516 IXGBE_COMPUTE_BKT_HASH_ITERATION(4);
1517 IXGBE_COMPUTE_BKT_HASH_ITERATION(5);
1518 IXGBE_COMPUTE_BKT_HASH_ITERATION(6);
1519 IXGBE_COMPUTE_BKT_HASH_ITERATION(7);
1520 IXGBE_COMPUTE_BKT_HASH_ITERATION(8);
1521 IXGBE_COMPUTE_BKT_HASH_ITERATION(9);
1522 IXGBE_COMPUTE_BKT_HASH_ITERATION(10);
1523 IXGBE_COMPUTE_BKT_HASH_ITERATION(11);
1524 IXGBE_COMPUTE_BKT_HASH_ITERATION(12);
1525 IXGBE_COMPUTE_BKT_HASH_ITERATION(13);
1526 IXGBE_COMPUTE_BKT_HASH_ITERATION(14);
1527 IXGBE_COMPUTE_BKT_HASH_ITERATION(15);
1528
1529 /*
1530 * Limit hash to 13 bits since max bucket count is 8K.
1531 * Store result at the end of the input stream.
1532 */
1533 input->formatted.bkt_hash = bucket_hash & 0x1FFF;
1534 }
1535
1536 /**
1537 * ixgbe_get_fdirtcpm_82599 - generate a tcp port from atr_input_masks
1538 * @input_mask: mask to be bit swapped
1539 *
1540 * The source and destination port masks for flow director are bit swapped
1541 * in that bit 15 effects bit 0, 14 effects 1, 13, 2 etc. In order to
1542 * generate a correctly swapped value we need to bit swap the mask and that
1543 * is what is accomplished by this function.
1544 **/
1545 static u32 ixgbe_get_fdirtcpm_82599(union ixgbe_atr_input *input_mask)
1546 {
1547 u32 mask = IXGBE_NTOHS(input_mask->formatted.dst_port);
1548 mask <<= IXGBE_FDIRTCPM_DPORTM_SHIFT;
1549 mask |= IXGBE_NTOHS(input_mask->formatted.src_port);
1550 mask = ((mask & 0x55555555) << 1) | ((mask & 0xAAAAAAAA) >> 1);
1551 mask = ((mask & 0x33333333) << 2) | ((mask & 0xCCCCCCCC) >> 2);
1552 mask = ((mask & 0x0F0F0F0F) << 4) | ((mask & 0xF0F0F0F0) >> 4);
1553 return ((mask & 0x00FF00FF) << 8) | ((mask & 0xFF00FF00) >> 8);
1554 }
1555
1556 /*
1557 * These two macros are meant to address the fact that we have registers
1558 * that are either all or in part big-endian. As a result on big-endian
1559 * systems we will end up byte swapping the value to little-endian before
1560 * it is byte swapped again and written to the hardware in the original
1561 * big-endian format.
1562 */
1563 #define IXGBE_STORE_AS_BE32(_value) \
1564 (((u32)(_value) >> 24) | (((u32)(_value) & 0x00FF0000) >> 8) | \
1565 (((u32)(_value) & 0x0000FF00) << 8) | ((u32)(_value) << 24))
1566
1567 #define IXGBE_WRITE_REG_BE32(a, reg, value) \
1568 IXGBE_WRITE_REG((a), (reg), IXGBE_STORE_AS_BE32(IXGBE_NTOHL(value)))
1569
1570 #define IXGBE_STORE_AS_BE16(_value) \
1571 IXGBE_NTOHS(((u16)(_value) >> 8) | ((u16)(_value) << 8))
1572
1573 s32 ixgbe_fdir_set_input_mask_82599(struct ixgbe_hw *hw,
1574 union ixgbe_atr_input *input_mask)
1575 {
1576 /* mask IPv6 since it is currently not supported */
1577 u32 fdirm = IXGBE_FDIRM_DIPv6;
1578 u32 fdirtcpm;
1579
1580 DEBUGFUNC("ixgbe_fdir_set_atr_input_mask_82599");
1581
1582 /*
1583 * Program the relevant mask registers. If src/dst_port or src/dst_addr
1584 * are zero, then assume a full mask for that field. Also assume that
1585 * a VLAN of 0 is unspecified, so mask that out as well. L4type
1586 * cannot be masked out in this implementation.
1587 *
1588 * This also assumes IPv4 only. IPv6 masking isn't supported at this
1589 * point in time.
1590 */
1591
1592 /* verify bucket hash is cleared on hash generation */
1593 if (input_mask->formatted.bkt_hash)
1594 DEBUGOUT(" bucket hash should always be 0 in mask\n");
1595
1596 /* Program FDIRM and verify partial masks */
1597 switch (input_mask->formatted.vm_pool & 0x7F) {
1598 case 0x0:
1599 fdirm |= IXGBE_FDIRM_POOL;
1600 /* FALLTHRU */
1601 case 0x7F:
1602 break;
1603 default:
1604 DEBUGOUT(" Error on vm pool mask\n");
1605 return IXGBE_ERR_CONFIG;
1606 }
1607
1608 switch (input_mask->formatted.flow_type & IXGBE_ATR_L4TYPE_MASK) {
1609 case 0x0:
1610 fdirm |= IXGBE_FDIRM_L4P;
1611 if (input_mask->formatted.dst_port ||
1612 input_mask->formatted.src_port) {
1613 DEBUGOUT(" Error on src/dst port mask\n");
1614 return IXGBE_ERR_CONFIG;
1615 }
1616 /* FALLTHRU */
1617 case IXGBE_ATR_L4TYPE_MASK:
1618 break;
1619 default:
1620 DEBUGOUT(" Error on flow type mask\n");
1621 return IXGBE_ERR_CONFIG;
1622 }
1623
1624 switch (IXGBE_NTOHS(input_mask->formatted.vlan_id) & 0xEFFF) {
1625 case 0x0000:
1626 /* mask VLAN ID, fall through to mask VLAN priority */
1627 fdirm |= IXGBE_FDIRM_VLANID;
1628 /* FALLTHRU */
1629 case 0x0FFF:
1630 /* mask VLAN priority */
1631 fdirm |= IXGBE_FDIRM_VLANP;
1632 break;
1633 case 0xE000:
1634 /* mask VLAN ID only, fall through */
1635 fdirm |= IXGBE_FDIRM_VLANID;
1636 /* FALLTHRU */
1637 case 0xEFFF:
1638 /* no VLAN fields masked */
1639 break;
1640 default:
1641 DEBUGOUT(" Error on VLAN mask\n");
1642 return IXGBE_ERR_CONFIG;
1643 }
1644
1645 switch (input_mask->formatted.flex_bytes & 0xFFFF) {
1646 case 0x0000:
1647 /* Mask Flex Bytes, fall through */
1648 fdirm |= IXGBE_FDIRM_FLEX;
1649 /* FALLTHRU */
1650 case 0xFFFF:
1651 break;
1652 default:
1653 DEBUGOUT(" Error on flexible byte mask\n");
1654 return IXGBE_ERR_CONFIG;
1655 }
1656
1657 /* Now mask VM pool and destination IPv6 - bits 5 and 2 */
1658 IXGBE_WRITE_REG(hw, IXGBE_FDIRM, fdirm);
1659
1660 /* store the TCP/UDP port masks, bit reversed from port layout */
1661 fdirtcpm = ixgbe_get_fdirtcpm_82599(input_mask);
1662
1663 /* write both the same so that UDP and TCP use the same mask */
1664 IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, ~fdirtcpm);
1665 IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, ~fdirtcpm);
1666
1667 /* store source and destination IP masks (big-enian) */
1668 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M,
1669 ~input_mask->formatted.src_ip[0]);
1670 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M,
1671 ~input_mask->formatted.dst_ip[0]);
1672
1673 return IXGBE_SUCCESS;
1674 }
1675
1676 s32 ixgbe_fdir_write_perfect_filter_82599(struct ixgbe_hw *hw,
1677 union ixgbe_atr_input *input,
1678 u16 soft_id, u8 queue)
1679 {
1680 u32 fdirport, fdirvlan, fdirhash, fdircmd;
1681
1682 DEBUGFUNC("ixgbe_fdir_write_perfect_filter_82599");
1683
1684 /* currently IPv6 is not supported, must be programmed with 0 */
1685 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(0),
1686 input->formatted.src_ip[0]);
1687 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(1),
1688 input->formatted.src_ip[1]);
1689 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(2),
1690 input->formatted.src_ip[2]);
1691
1692 /* record the source address (big-endian) */
1693 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPSA, input->formatted.src_ip[0]);
1694
1695 /* record the first 32 bits of the destination address (big-endian) */
1696 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPDA, input->formatted.dst_ip[0]);
1697
1698 /* record source and destination port (little-endian)*/
1699 fdirport = IXGBE_NTOHS(input->formatted.dst_port);
1700 fdirport <<= IXGBE_FDIRPORT_DESTINATION_SHIFT;
1701 fdirport |= IXGBE_NTOHS(input->formatted.src_port);
1702 IXGBE_WRITE_REG(hw, IXGBE_FDIRPORT, fdirport);
1703
1704 /* record vlan (little-endian) and flex_bytes(big-endian) */
1705 fdirvlan = IXGBE_STORE_AS_BE16(input->formatted.flex_bytes);
1706 fdirvlan <<= IXGBE_FDIRVLAN_FLEX_SHIFT;
1707 fdirvlan |= IXGBE_NTOHS(input->formatted.vlan_id);
1708 IXGBE_WRITE_REG(hw, IXGBE_FDIRVLAN, fdirvlan);
1709
1710 /* configure FDIRHASH register */
1711 fdirhash = input->formatted.bkt_hash;
1712 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT;
1713 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1714
1715 /*
1716 * flush all previous writes to make certain registers are
1717 * programmed prior to issuing the command
1718 */
1719 IXGBE_WRITE_FLUSH(hw);
1720
1721 /* configure FDIRCMD register */
1722 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE |
1723 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN;
1724 if (queue == IXGBE_FDIR_DROP_QUEUE)
1725 fdircmd |= IXGBE_FDIRCMD_DROP;
1726 fdircmd |= input->formatted.flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT;
1727 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT;
1728 fdircmd |= (u32)input->formatted.vm_pool << IXGBE_FDIRCMD_VT_POOL_SHIFT;
1729
1730 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, fdircmd);
1731
1732 return IXGBE_SUCCESS;
1733 }
1734
1735 s32 ixgbe_fdir_erase_perfect_filter_82599(struct ixgbe_hw *hw,
1736 union ixgbe_atr_input *input,
1737 u16 soft_id)
1738 {
1739 u32 fdirhash;
1740 u32 fdircmd = 0;
1741 u32 retry_count;
1742 s32 err = IXGBE_SUCCESS;
1743
1744 /* configure FDIRHASH register */
1745 fdirhash = input->formatted.bkt_hash;
1746 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT;
1747 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1748
1749 /* flush hash to HW */
1750 IXGBE_WRITE_FLUSH(hw);
1751
1752 /* Query if filter is present */
1753 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, IXGBE_FDIRCMD_CMD_QUERY_REM_FILT);
1754
1755 for (retry_count = 10; retry_count; retry_count--) {
1756 /* allow 10us for query to process */
1757 usec_delay(10);
1758 /* verify query completed successfully */
1759 fdircmd = IXGBE_READ_REG(hw, IXGBE_FDIRCMD);
1760 if (!(fdircmd & IXGBE_FDIRCMD_CMD_MASK))
1761 break;
1762 }
1763
1764 if (!retry_count)
1765 err = IXGBE_ERR_FDIR_REINIT_FAILED;
1766
1767 /* if filter exists in hardware then remove it */
1768 if (fdircmd & IXGBE_FDIRCMD_FILTER_VALID) {
1769 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1770 IXGBE_WRITE_FLUSH(hw);
1771 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1772 IXGBE_FDIRCMD_CMD_REMOVE_FLOW);
1773 }
1774
1775 return err;
1776 }
1777
1778 /**
1779 * ixgbe_fdir_add_perfect_filter_82599 - Adds a perfect filter
1780 * @hw: pointer to hardware structure
1781 * @input: input bitstream
1782 * @input_mask: mask for the input bitstream
1783 * @soft_id: software index for the filters
1784 * @queue: queue index to direct traffic to
1785 *
1786 * Note that the caller to this function must lock before calling, since the
1787 * hardware writes must be protected from one another.
1788 **/
1789 s32 ixgbe_fdir_add_perfect_filter_82599(struct ixgbe_hw *hw,
1790 union ixgbe_atr_input *input,
1791 union ixgbe_atr_input *input_mask,
1792 u16 soft_id, u8 queue)
1793 {
1794 s32 err = IXGBE_ERR_CONFIG;
1795
1796 DEBUGFUNC("ixgbe_fdir_add_perfect_filter_82599");
1797
1798 /*
1799 * Check flow_type formatting, and bail out before we touch the hardware
1800 * if there's a configuration issue
1801 */
1802 switch (input->formatted.flow_type) {
1803 case IXGBE_ATR_FLOW_TYPE_IPV4:
1804 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK;
1805 if (input->formatted.dst_port || input->formatted.src_port) {
1806 DEBUGOUT(" Error on src/dst port\n");
1807 return IXGBE_ERR_CONFIG;
1808 }
1809 break;
1810 case IXGBE_ATR_FLOW_TYPE_SCTPV4:
1811 if (input->formatted.dst_port || input->formatted.src_port) {
1812 DEBUGOUT(" Error on src/dst port\n");
1813 return IXGBE_ERR_CONFIG;
1814 }
1815 /* FALLTHRU */
1816 case IXGBE_ATR_FLOW_TYPE_TCPV4:
1817 case IXGBE_ATR_FLOW_TYPE_UDPV4:
1818 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK |
1819 IXGBE_ATR_L4TYPE_MASK;
1820 break;
1821 default:
1822 DEBUGOUT(" Error on flow type input\n");
1823 return err;
1824 }
1825
1826 /* program input mask into the HW */
1827 err = ixgbe_fdir_set_input_mask_82599(hw, input_mask);
1828 if (err)
1829 return err;
1830
1831 /* apply mask and compute/store hash */
1832 ixgbe_atr_compute_perfect_hash_82599(input, input_mask);
1833
1834 /* program filters to filter memory */
1835 return ixgbe_fdir_write_perfect_filter_82599(hw, input,
1836 soft_id, queue);
1837 }
1838
1839 /**
1840 * ixgbe_read_analog_reg8_82599 - Reads 8 bit Omer analog register
1841 * @hw: pointer to hardware structure
1842 * @reg: analog register to read
1843 * @val: read value
1844 *
1845 * Performs read operation to Omer analog register specified.
1846 **/
1847 s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val)
1848 {
1849 u32 core_ctl;
1850
1851 DEBUGFUNC("ixgbe_read_analog_reg8_82599");
1852
1853 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, IXGBE_CORECTL_WRITE_CMD |
1854 (reg << 8));
1855 IXGBE_WRITE_FLUSH(hw);
1856 usec_delay(10);
1906
1907 /* We need to run link autotry after the driver loads */
1908 hw->mac.autotry_restart = TRUE;
1909
1910 if (ret_val == IXGBE_SUCCESS)
1911 ret_val = ixgbe_verify_fw_version_82599(hw);
1912 out:
1913 return ret_val;
1914 }
1915
1916 /**
1917 * ixgbe_identify_phy_82599 - Get physical layer module
1918 * @hw: pointer to hardware structure
1919 *
1920 * Determines the physical layer module found on the current adapter.
1921 * If PHY already detected, maintains current PHY type in hw struct,
1922 * otherwise executes the PHY detection routine.
1923 **/
1924 s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw)
1925 {
1926 s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
1927
1928 DEBUGFUNC("ixgbe_identify_phy_82599");
1929
1930 /* Detect PHY if not unknown - returns success if already detected. */
1931 status = ixgbe_identify_phy_generic(hw);
1932 if (status != IXGBE_SUCCESS) {
1933 /* 82599 10GBASE-T requires an external PHY */
1934 if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper)
1935 goto out;
1936 else
1937 status = ixgbe_identify_module_generic(hw);
1938 }
1939
1940 /* Set PHY type none if no PHY detected */
1941 if (hw->phy.type == ixgbe_phy_unknown) {
1942 hw->phy.type = ixgbe_phy_none;
1943 status = IXGBE_SUCCESS;
1944 }
1945
1946 /* Return error if SFP module has been detected but is not supported */
1947 if (hw->phy.type == ixgbe_phy_sfp_unsupported)
1948 status = IXGBE_ERR_SFP_NOT_SUPPORTED;
1949
1950 out:
1951 return status;
1952 }
1953
1954 /**
1955 * ixgbe_get_supported_physical_layer_82599 - Returns physical layer type
1956 * @hw: pointer to hardware structure
1957 *
1958 * Determines physical layer capabilities of the current configuration.
1959 **/
1960 u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw)
1961 {
1962 u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
1963 u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
1964 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
1965 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
1966 u32 pma_pmd_10g_parallel = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK;
1967 u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
1968 u16 ext_ability = 0;
1969 u8 comp_codes_10g = 0;
1970 u8 comp_codes_1g = 0;
1971
1972 DEBUGFUNC("ixgbe_get_support_physical_layer_82599");
1973
1974 hw->phy.ops.identify(hw);
1975
1976 switch (hw->phy.type) {
1977 case ixgbe_phy_tn:
1978 case ixgbe_phy_cu_unknown:
1979 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY,
1980 IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability);
1981 if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY)
1982 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
1983 if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
1984 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
1985 if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY)
1986 physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
1987 goto out;
1988 default:
1989 break;
1990 }
1991
1992 switch (autoc & IXGBE_AUTOC_LMS_MASK) {
1993 case IXGBE_AUTOC_LMS_1G_AN:
1994 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
1995 if (pma_pmd_1g == IXGBE_AUTOC_1G_KX_BX) {
1996 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX |
1997 IXGBE_PHYSICAL_LAYER_1000BASE_BX;
1998 goto out;
1999 }
2000 /* SFI mode so read SFP module */
2001 goto sfp_check;
2002 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
2003 if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_CX4)
2004 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
2005 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_KX4)
2006 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
2007 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_XAUI)
2008 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_XAUI;
2009 goto out;
2010 case IXGBE_AUTOC_LMS_10G_SERIAL:
2011 if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_KR) {
2012 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR;
2013 goto out;
2014 } else if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)
2015 goto sfp_check;
2016 break;
2017 case IXGBE_AUTOC_LMS_KX4_KX_KR:
2018 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
2019 if (autoc & IXGBE_AUTOC_KX_SUPP)
2020 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX;
2021 if (autoc & IXGBE_AUTOC_KX4_SUPP)
2022 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
2023 if (autoc & IXGBE_AUTOC_KR_SUPP)
2024 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KR;
2025 goto out;
2026 default:
2027 goto out;
2028 }
2029
2030 sfp_check:
2031 /* SFP check must be done last since DA modules are sometimes used to
2032 * test KR mode - we need to id KR mode correctly before SFP module.
2033 * Call identify_sfp because the pluggable module may have changed */
2034 hw->phy.ops.identify_sfp(hw);
2035 if (hw->phy.sfp_type == ixgbe_sfp_type_not_present)
2036 goto out;
2037
2038 switch (hw->phy.type) {
2039 case ixgbe_phy_sfp_passive_tyco:
2040 case ixgbe_phy_sfp_passive_unknown:
2041 physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
2042 break;
2043 case ixgbe_phy_sfp_ftl_active:
2044 case ixgbe_phy_sfp_active_unknown:
2045 physical_layer = IXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA;
2046 break;
2047 case ixgbe_phy_sfp_avago:
2048 case ixgbe_phy_sfp_ftl:
2049 case ixgbe_phy_sfp_intel:
2050 case ixgbe_phy_sfp_unknown:
2051 hw->phy.ops.read_i2c_eeprom(hw,
2052 IXGBE_SFF_1GBE_COMP_CODES, &comp_codes_1g);
2053 hw->phy.ops.read_i2c_eeprom(hw,
2054 IXGBE_SFF_10GBE_COMP_CODES, &comp_codes_10g);
2055 if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)
2056 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
2057 else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE)
2058 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
2059 else if (comp_codes_1g & IXGBE_SFF_1GBASET_CAPABLE)
2060 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_T;
2061 else if (comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE)
2062 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_SX;
2063 break;
2064 default:
2065 break;
2066 }
2067
2068 out:
2069 return physical_layer;
2070 }
2071
2072 /**
2073 * ixgbe_enable_rx_dma_82599 - Enable the Rx DMA unit on 82599
2074 * @hw: pointer to hardware structure
2075 * @regval: register value to write to RXCTRL
2076 *
2077 * Enables the Rx DMA unit for 82599
2078 **/
2079 s32 ixgbe_enable_rx_dma_82599(struct ixgbe_hw *hw, u32 regval)
2080 {
2081
2082 DEBUGFUNC("ixgbe_enable_rx_dma_82599");
2083
2084 /*
2085 * Workaround for 82599 silicon errata when enabling the Rx datapath.
2086 * If traffic is incoming before we enable the Rx unit, it could hang
2087 * the Rx DMA unit. Therefore, make sure the security engine is
2088 * completely disabled prior to enabling the Rx unit.
2089 */
2090
2091 hw->mac.ops.disable_sec_rx_path(hw);
2092
2093 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, regval);
2094
2095 hw->mac.ops.enable_sec_rx_path(hw);
2096
2097 return IXGBE_SUCCESS;
2098 }
2099
2100 /**
2101 * ixgbe_verify_fw_version_82599 - verify fw version for 82599
2102 * @hw: pointer to hardware structure
2103 *
2104 * Verifies that installed the firmware version is 0.6 or higher
2105 * for SFI devices. All 82599 SFI devices should have version 0.6 or higher.
2106 *
2107 * Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or
2108 * if the FW version is not supported.
2109 **/
2110 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw)
2111 {
2112 s32 status = IXGBE_ERR_EEPROM_VERSION;
2113 u16 fw_offset, fw_ptp_cfg_offset;
2114 u16 fw_version = 0;
2115
2116 DEBUGFUNC("ixgbe_verify_fw_version_82599");
2117
2118 /* firmware check is only necessary for SFI devices */
2119 if (hw->phy.media_type != ixgbe_media_type_fiber) {
2120 status = IXGBE_SUCCESS;
2121 goto fw_version_out;
2122 }
2123
2124 /* get the offset to the Firmware Module block */
2125 hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset);
2126
2127 if ((fw_offset == 0) || (fw_offset == 0xFFFF))
2128 goto fw_version_out;
2129
2130 /* get the offset to the Pass Through Patch Configuration block */
2131 hw->eeprom.ops.read(hw, (fw_offset +
2132 IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR),
2133 &fw_ptp_cfg_offset);
2134
2135 if ((fw_ptp_cfg_offset == 0) || (fw_ptp_cfg_offset == 0xFFFF))
2136 goto fw_version_out;
2137
2138 /* get the firmware version */
2139 hw->eeprom.ops.read(hw, (fw_ptp_cfg_offset +
2140 IXGBE_FW_PATCH_VERSION_4), &fw_version);
2141
2142 if (fw_version > 0x5)
2143 status = IXGBE_SUCCESS;
2144
2145 fw_version_out:
2146 return status;
2147 }
2148
2149 /**
2150 * ixgbe_verify_lesm_fw_enabled_82599 - Checks LESM FW module state.
2151 * @hw: pointer to hardware structure
2152 *
2153 * Returns TRUE if the LESM FW module is present and enabled. Otherwise
2154 * returns FALSE. Smart Speed must be disabled if LESM FW module is enabled.
2155 **/
2156 bool ixgbe_verify_lesm_fw_enabled_82599(struct ixgbe_hw *hw)
2157 {
2158 bool lesm_enabled = FALSE;
2159 u16 fw_offset, fw_lesm_param_offset, fw_lesm_state;
2160 s32 status;
2161
2162 DEBUGFUNC("ixgbe_verify_lesm_fw_enabled_82599");
2163
2164 /* get the offset to the Firmware Module block */
2165 status = hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset);
2166
2167 if ((status != IXGBE_SUCCESS) ||
2168 (fw_offset == 0) || (fw_offset == 0xFFFF))
2169 goto out;
2170
2171 /* get the offset to the LESM Parameters block */
2172 status = hw->eeprom.ops.read(hw, (fw_offset +
2173 IXGBE_FW_LESM_PARAMETERS_PTR),
2174 &fw_lesm_param_offset);
2175
2176 if ((status != IXGBE_SUCCESS) ||
2177 (fw_lesm_param_offset == 0) || (fw_lesm_param_offset == 0xFFFF))
2178 goto out;
2179
2180 /* get the lesm state word */
2181 status = hw->eeprom.ops.read(hw, (fw_lesm_param_offset +
2182 IXGBE_FW_LESM_STATE_1),
2183 &fw_lesm_state);
2184
2185 if ((status == IXGBE_SUCCESS) &&
2186 (fw_lesm_state & IXGBE_FW_LESM_STATE_ENABLED))
2187 lesm_enabled = TRUE;
2188
2189 out:
2190 return lesm_enabled;
2191 }
2192
2193 /**
2194 * ixgbe_read_eeprom_buffer_82599 - Read EEPROM word(s) using
2195 * fastest available method
2196 *
2197 * @hw: pointer to hardware structure
2198 * @offset: offset of word in EEPROM to read
2199 * @words: number of words
2200 * @data: word(s) read from the EEPROM
2239 u16 offset, u16 *data)
2240 {
2241 struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
2242 s32 ret_val = IXGBE_ERR_CONFIG;
2243
2244 DEBUGFUNC("ixgbe_read_eeprom_82599");
2245
2246 /*
2247 * If EEPROM is detected and can be addressed using 14 bits,
2248 * use EERD otherwise use bit bang
2249 */
2250 if ((eeprom->type == ixgbe_eeprom_spi) &&
2251 (offset <= IXGBE_EERD_MAX_ADDR))
2252 ret_val = ixgbe_read_eerd_generic(hw, offset, data);
2253 else
2254 ret_val = ixgbe_read_eeprom_bit_bang_generic(hw, offset, data);
2255
2256 return ret_val;
2257 }
2258
2259
|
1 /******************************************************************************
2
3 Copyright (c) 2001-2015, Intel Corporation
4 All rights reserved.
5
6 Redistribution and use in source and binary forms, with or without
7 modification, are permitted provided that the following conditions are met:
8
9 1. Redistributions of source code must retain the above copyright notice,
10 this list of conditions and the following disclaimer.
11
12 2. Redistributions in binary form must reproduce the above copyright
13 notice, this list of conditions and the following disclaimer in the
14 documentation and/or other materials provided with the distribution.
15
16 3. Neither the name of the Intel Corporation nor the names of its
17 contributors may be used to endorse or promote products derived from
18 this software without specific prior written permission.
19
20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
30 POSSIBILITY OF SUCH DAMAGE.
31
32 ******************************************************************************/
33 /*$FreeBSD$*/
34
35 #include "ixgbe_type.h"
36 #include "ixgbe_82599.h"
37 #include "ixgbe_api.h"
38 #include "ixgbe_common.h"
39 #include "ixgbe_phy.h"
40
41 #define IXGBE_82599_MAX_TX_QUEUES 128
42 #define IXGBE_82599_MAX_RX_QUEUES 128
43 #define IXGBE_82599_RAR_ENTRIES 128
44 #define IXGBE_82599_MC_TBL_SIZE 128
45 #define IXGBE_82599_VFT_TBL_SIZE 128
46 #define IXGBE_82599_RX_PB_SIZE 512
47
48 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
49 ixgbe_link_speed speed,
50 bool autoneg_wait_to_complete);
51 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw);
52 static s32 ixgbe_read_eeprom_82599(struct ixgbe_hw *hw,
53 u16 offset, u16 *data);
54 static s32 ixgbe_read_eeprom_buffer_82599(struct ixgbe_hw *hw, u16 offset,
55 u16 words, u16 *data);
56 static s32 ixgbe_read_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset,
57 u8 dev_addr, u8 *data);
58 static s32 ixgbe_write_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset,
59 u8 dev_addr, u8 data);
60
61 void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)
62 {
63 struct ixgbe_mac_info *mac = &hw->mac;
64
65 DEBUGFUNC("ixgbe_init_mac_link_ops_82599");
66
67 /*
68 * enable the laser control functions for SFP+ fiber
69 * and MNG not enabled
70 */
71 if ((mac->ops.get_media_type(hw) == ixgbe_media_type_fiber) &&
72 !ixgbe_mng_enabled(hw)) {
73 mac->ops.disable_tx_laser =
74 ixgbe_disable_tx_laser_multispeed_fiber;
75 mac->ops.enable_tx_laser =
76 ixgbe_enable_tx_laser_multispeed_fiber;
77 mac->ops.flap_tx_laser = ixgbe_flap_tx_laser_multispeed_fiber;
78
79 } else {
80 mac->ops.disable_tx_laser = NULL;
81 mac->ops.enable_tx_laser = NULL;
82 mac->ops.flap_tx_laser = NULL;
83 }
84
85 if (hw->phy.multispeed_fiber) {
86 /* Set up dual speed SFP+ support */
87 mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
88 mac->ops.setup_mac_link = ixgbe_setup_mac_link_82599;
89 mac->ops.set_rate_select_speed =
90 ixgbe_set_hard_rate_select_speed;
91 if (ixgbe_get_media_type(hw) == ixgbe_media_type_fiber_fixed)
92 mac->ops.set_rate_select_speed =
93 ixgbe_set_soft_rate_select_speed;
94 } else {
95 if ((ixgbe_get_media_type(hw) == ixgbe_media_type_backplane) &&
96 (hw->phy.smart_speed == ixgbe_smart_speed_auto ||
97 hw->phy.smart_speed == ixgbe_smart_speed_on) &&
98 !ixgbe_verify_lesm_fw_enabled_82599(hw)) {
99 mac->ops.setup_link = ixgbe_setup_mac_link_smartspeed;
100 } else {
101 mac->ops.setup_link = ixgbe_setup_mac_link_82599;
102 }
103 }
104 }
105
106 /**
107 * ixgbe_init_phy_ops_82599 - PHY/SFP specific init
108 * @hw: pointer to hardware structure
109 *
110 * Initialize any function pointers that were not able to be
111 * set during init_shared_code because the PHY/SFP type was
112 * not known. Perform the SFP init if necessary.
113 *
114 **/
115 s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw)
116 {
117 struct ixgbe_mac_info *mac = &hw->mac;
118 struct ixgbe_phy_info *phy = &hw->phy;
119 s32 ret_val = IXGBE_SUCCESS;
120 u32 esdp;
121
122 DEBUGFUNC("ixgbe_init_phy_ops_82599");
123
124 if (hw->device_id == IXGBE_DEV_ID_82599_QSFP_SF_QP) {
125 /* Store flag indicating I2C bus access control unit. */
126 hw->phy.qsfp_shared_i2c_bus = TRUE;
127
128 /* Initialize access to QSFP+ I2C bus */
129 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
130 esdp |= IXGBE_ESDP_SDP0_DIR;
131 esdp &= ~IXGBE_ESDP_SDP1_DIR;
132 esdp &= ~IXGBE_ESDP_SDP0;
133 esdp &= ~IXGBE_ESDP_SDP0_NATIVE;
134 esdp &= ~IXGBE_ESDP_SDP1_NATIVE;
135 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
136 IXGBE_WRITE_FLUSH(hw);
137
138 phy->ops.read_i2c_byte = ixgbe_read_i2c_byte_82599;
139 phy->ops.write_i2c_byte = ixgbe_write_i2c_byte_82599;
140 }
141 /* Identify the PHY or SFP module */
142 ret_val = phy->ops.identify(hw);
143 if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED)
144 goto init_phy_ops_out;
145
146 /* Setup function pointers based on detected SFP module and speeds */
147 ixgbe_init_mac_link_ops_82599(hw);
148 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown)
149 hw->phy.ops.reset = NULL;
150
151 /* If copper media, overwrite with copper function pointers */
152 if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
153 mac->ops.setup_link = ixgbe_setup_copper_link_82599;
154 mac->ops.get_link_capabilities =
155 ixgbe_get_copper_link_capabilities_generic;
156 }
157
158 /* Set necessary function pointers based on PHY type */
159 switch (hw->phy.type) {
160 case ixgbe_phy_tn:
161 phy->ops.setup_link = ixgbe_setup_phy_link_tnx;
162 phy->ops.check_link = ixgbe_check_phy_link_tnx;
163 phy->ops.get_firmware_version =
164 ixgbe_get_phy_firmware_version_tnx;
165 break;
166 default:
167 break;
168 }
169 init_phy_ops_out:
170 return ret_val;
171 }
172
173 s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw)
174 {
175 s32 ret_val = IXGBE_SUCCESS;
176 u16 list_offset, data_offset, data_value;
177
178 DEBUGFUNC("ixgbe_setup_sfp_modules_82599");
179
180 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) {
181 ixgbe_init_mac_link_ops_82599(hw);
182
183 hw->phy.ops.reset = NULL;
184
185 ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset,
186 &data_offset);
187 if (ret_val != IXGBE_SUCCESS)
188 goto setup_sfp_out;
189
190 /* PHY config will finish before releasing the semaphore */
191 ret_val = hw->mac.ops.acquire_swfw_sync(hw,
192 IXGBE_GSSR_MAC_CSR_SM);
193 if (ret_val != IXGBE_SUCCESS) {
194 ret_val = IXGBE_ERR_SWFW_SYNC;
195 goto setup_sfp_out;
196 }
197
198 if (hw->eeprom.ops.read(hw, ++data_offset, &data_value))
199 goto setup_sfp_err;
200 while (data_value != 0xffff) {
201 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, data_value);
202 IXGBE_WRITE_FLUSH(hw);
203 if (hw->eeprom.ops.read(hw, ++data_offset, &data_value))
204 goto setup_sfp_err;
205 }
206
207 /* Release the semaphore */
208 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
209 /* Delay obtaining semaphore again to allow FW access
210 * prot_autoc_write uses the semaphore too.
211 */
212 msec_delay(hw->eeprom.semaphore_delay);
213
214 /* Restart DSP and set SFI mode */
215 ret_val = hw->mac.ops.prot_autoc_write(hw,
216 hw->mac.orig_autoc | IXGBE_AUTOC_LMS_10G_SERIAL,
217 FALSE);
218
219 if (ret_val) {
220 DEBUGOUT("sfp module setup not complete\n");
221 ret_val = IXGBE_ERR_SFP_SETUP_NOT_COMPLETE;
222 goto setup_sfp_out;
223 }
224
225 }
226
227 setup_sfp_out:
228 return ret_val;
229
230 setup_sfp_err:
231 /* Release the semaphore */
232 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
233 /* Delay obtaining semaphore again to allow FW access */
234 msec_delay(hw->eeprom.semaphore_delay);
235 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE,
236 "eeprom read at offset %d failed", data_offset);
237 return IXGBE_ERR_PHY;
238 }
239
240 /**
241 * prot_autoc_read_82599 - Hides MAC differences needed for AUTOC read
242 * @hw: pointer to hardware structure
243 * @locked: Return the if we locked for this read.
244 * @reg_val: Value we read from AUTOC
245 *
246 * For this part (82599) we need to wrap read-modify-writes with a possible
247 * FW/SW lock. It is assumed this lock will be freed with the next
248 * prot_autoc_write_82599().
249 */
250 s32 prot_autoc_read_82599(struct ixgbe_hw *hw, bool *locked, u32 *reg_val)
251 {
252 s32 ret_val;
253
254 *locked = FALSE;
255 /* If LESM is on then we need to hold the SW/FW semaphore. */
256 if (ixgbe_verify_lesm_fw_enabled_82599(hw)) {
257 ret_val = hw->mac.ops.acquire_swfw_sync(hw,
258 IXGBE_GSSR_MAC_CSR_SM);
259 if (ret_val != IXGBE_SUCCESS)
260 return IXGBE_ERR_SWFW_SYNC;
261
262 *locked = TRUE;
263 }
264
265 *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC);
266 return IXGBE_SUCCESS;
267 }
268
269 /**
270 * prot_autoc_write_82599 - Hides MAC differences needed for AUTOC write
271 * @hw: pointer to hardware structure
272 * @reg_val: value to write to AUTOC
273 * @locked: bool to indicate whether the SW/FW lock was already taken by
274 * previous proc_autoc_read_82599.
275 *
276 * This part (82599) may need to hold the SW/FW lock around all writes to
277 * AUTOC. Likewise after a write we need to do a pipeline reset.
278 */
279 s32 prot_autoc_write_82599(struct ixgbe_hw *hw, u32 autoc, bool locked)
280 {
281 s32 ret_val = IXGBE_SUCCESS;
282
283 /* Blocked by MNG FW so bail */
284 if (ixgbe_check_reset_blocked(hw))
285 goto out;
286
287 /* We only need to get the lock if:
288 * - We didn't do it already (in the read part of a read-modify-write)
289 * - LESM is enabled.
290 */
291 if (!locked && ixgbe_verify_lesm_fw_enabled_82599(hw)) {
292 ret_val = hw->mac.ops.acquire_swfw_sync(hw,
293 IXGBE_GSSR_MAC_CSR_SM);
294 if (ret_val != IXGBE_SUCCESS)
295 return IXGBE_ERR_SWFW_SYNC;
296
297 locked = TRUE;
298 }
299
300 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
301 ret_val = ixgbe_reset_pipeline_82599(hw);
302
303 out:
304 /* Free the SW/FW semaphore as we either grabbed it here or
305 * already had it when this function was called.
306 */
307 if (locked)
308 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
309
310 return ret_val;
311 }
312
313 /**
314 * ixgbe_init_ops_82599 - Inits func ptrs and MAC type
315 * @hw: pointer to hardware structure
316 *
317 * Initialize the function pointers and assign the MAC type for 82599.
318 * Does not touch the hardware.
319 **/
320
321 s32 ixgbe_init_ops_82599(struct ixgbe_hw *hw)
322 {
323 struct ixgbe_mac_info *mac = &hw->mac;
324 struct ixgbe_phy_info *phy = &hw->phy;
325 struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
326 s32 ret_val;
327
328 DEBUGFUNC("ixgbe_init_ops_82599");
329
330 ixgbe_init_phy_ops_generic(hw);
331 ret_val = ixgbe_init_ops_generic(hw);
332
333 /* PHY */
334 phy->ops.identify = ixgbe_identify_phy_82599;
335 phy->ops.init = ixgbe_init_phy_ops_82599;
336
337 /* MAC */
338 mac->ops.reset_hw = ixgbe_reset_hw_82599;
339 mac->ops.enable_relaxed_ordering = ixgbe_enable_relaxed_ordering_gen2;
340 mac->ops.get_media_type = ixgbe_get_media_type_82599;
341 mac->ops.get_supported_physical_layer =
342 ixgbe_get_supported_physical_layer_82599;
343 mac->ops.disable_sec_rx_path = ixgbe_disable_sec_rx_path_generic;
344 mac->ops.enable_sec_rx_path = ixgbe_enable_sec_rx_path_generic;
345 mac->ops.enable_rx_dma = ixgbe_enable_rx_dma_82599;
346 mac->ops.read_analog_reg8 = ixgbe_read_analog_reg8_82599;
347 mac->ops.write_analog_reg8 = ixgbe_write_analog_reg8_82599;
348 mac->ops.start_hw = ixgbe_start_hw_82599;
349 mac->ops.get_san_mac_addr = ixgbe_get_san_mac_addr_generic;
350 mac->ops.set_san_mac_addr = ixgbe_set_san_mac_addr_generic;
351 mac->ops.get_device_caps = ixgbe_get_device_caps_generic;
352 mac->ops.get_wwn_prefix = ixgbe_get_wwn_prefix_generic;
353 mac->ops.get_fcoe_boot_status = ixgbe_get_fcoe_boot_status_generic;
354 mac->ops.prot_autoc_read = prot_autoc_read_82599;
355 mac->ops.prot_autoc_write = prot_autoc_write_82599;
356
357 /* RAR, Multicast, VLAN */
358 mac->ops.set_vmdq = ixgbe_set_vmdq_generic;
359 mac->ops.set_vmdq_san_mac = ixgbe_set_vmdq_san_mac_generic;
360 mac->ops.clear_vmdq = ixgbe_clear_vmdq_generic;
361 mac->ops.insert_mac_addr = ixgbe_insert_mac_addr_generic;
362 mac->rar_highwater = 1;
363 mac->ops.set_vfta = ixgbe_set_vfta_generic;
364 mac->ops.set_vlvf = ixgbe_set_vlvf_generic;
365 mac->ops.clear_vfta = ixgbe_clear_vfta_generic;
366 mac->ops.init_uta_tables = ixgbe_init_uta_tables_generic;
367 mac->ops.setup_sfp = ixgbe_setup_sfp_modules_82599;
368 mac->ops.set_mac_anti_spoofing = ixgbe_set_mac_anti_spoofing;
369 mac->ops.set_vlan_anti_spoofing = ixgbe_set_vlan_anti_spoofing;
370
371 /* Link */
372 mac->ops.get_link_capabilities = ixgbe_get_link_capabilities_82599;
373 mac->ops.check_link = ixgbe_check_mac_link_generic;
374 mac->ops.setup_rxpba = ixgbe_set_rxpba_generic;
375 ixgbe_init_mac_link_ops_82599(hw);
376
377 mac->mcft_size = IXGBE_82599_MC_TBL_SIZE;
378 mac->vft_size = IXGBE_82599_VFT_TBL_SIZE;
379 mac->num_rar_entries = IXGBE_82599_RAR_ENTRIES;
380 mac->rx_pb_size = IXGBE_82599_RX_PB_SIZE;
381 mac->max_rx_queues = IXGBE_82599_MAX_RX_QUEUES;
382 mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES;
383 mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw);
384
385 mac->arc_subsystem_valid = !!(IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw))
386 & IXGBE_FWSM_MODE_MASK);
387
388 hw->mbx.ops.init_params = ixgbe_init_mbx_params_pf;
389
390 /* EEPROM */
391 eeprom->ops.read = ixgbe_read_eeprom_82599;
392 eeprom->ops.read_buffer = ixgbe_read_eeprom_buffer_82599;
393
394 /* Manageability interface */
395 mac->ops.set_fw_drv_ver = ixgbe_set_fw_drv_ver_generic;
396
397
398 mac->ops.get_rtrup2tc = ixgbe_dcb_get_rtrup2tc_generic;
399
400 return ret_val;
401 }
402
403 /**
404 * ixgbe_get_link_capabilities_82599 - Determines link capabilities
405 * @hw: pointer to hardware structure
406 * @speed: pointer to link speed
407 * @autoneg: TRUE when autoneg or autotry is enabled
408 *
409 * Determines the link capabilities by reading the AUTOC register.
410 **/
411 s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw,
412 ixgbe_link_speed *speed,
413 bool *autoneg)
414 {
415 s32 status = IXGBE_SUCCESS;
416 u32 autoc = 0;
417
418 DEBUGFUNC("ixgbe_get_link_capabilities_82599");
419
420
421 /* Check if 1G SFP module. */
422 if (hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 ||
423 hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 ||
424 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
425 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
426 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
427 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
428 *speed = IXGBE_LINK_SPEED_1GB_FULL;
429 *autoneg = TRUE;
430 goto out;
431 }
432
433 /*
434 * Determine link capabilities based on the stored value of AUTOC,
435 * which represents EEPROM defaults. If AUTOC value has not
436 * been stored, use the current register values.
437 */
438 if (hw->mac.orig_link_settings_stored)
439 autoc = hw->mac.orig_autoc;
440 else
441 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
442
443 switch (autoc & IXGBE_AUTOC_LMS_MASK) {
444 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
445 *speed = IXGBE_LINK_SPEED_1GB_FULL;
446 *autoneg = FALSE;
447 break;
448
449 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
450 *speed = IXGBE_LINK_SPEED_10GB_FULL;
451 *autoneg = FALSE;
452 break;
453
454 case IXGBE_AUTOC_LMS_1G_AN:
455 *speed = IXGBE_LINK_SPEED_1GB_FULL;
456 *autoneg = TRUE;
457 break;
458
459 case IXGBE_AUTOC_LMS_10G_SERIAL:
460 *speed = IXGBE_LINK_SPEED_10GB_FULL;
461 *autoneg = FALSE;
462 break;
463
464 case IXGBE_AUTOC_LMS_KX4_KX_KR:
465 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
466 *speed = IXGBE_LINK_SPEED_UNKNOWN;
467 if (autoc & IXGBE_AUTOC_KR_SUPP)
468 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
469 if (autoc & IXGBE_AUTOC_KX4_SUPP)
470 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
471 if (autoc & IXGBE_AUTOC_KX_SUPP)
472 *speed |= IXGBE_LINK_SPEED_1GB_FULL;
473 *autoneg = TRUE;
474 break;
475
476 case IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII:
477 *speed = IXGBE_LINK_SPEED_100_FULL;
478 if (autoc & IXGBE_AUTOC_KR_SUPP)
479 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
480 if (autoc & IXGBE_AUTOC_KX4_SUPP)
481 *speed |= IXGBE_LINK_SPEED_10GB_FULL;
482 if (autoc & IXGBE_AUTOC_KX_SUPP)
483 *speed |= IXGBE_LINK_SPEED_1GB_FULL;
484 *autoneg = TRUE;
485 break;
486
487 case IXGBE_AUTOC_LMS_SGMII_1G_100M:
488 *speed = IXGBE_LINK_SPEED_1GB_FULL | IXGBE_LINK_SPEED_100_FULL;
489 *autoneg = FALSE;
490 break;
491
492 default:
493 status = IXGBE_ERR_LINK_SETUP;
494 goto out;
495 break;
496 }
497
498 if (hw->phy.multispeed_fiber) {
499 *speed |= IXGBE_LINK_SPEED_10GB_FULL |
500 IXGBE_LINK_SPEED_1GB_FULL;
501
502 /* QSFP must not enable full auto-negotiation
503 * Limited autoneg is enabled at 1G
504 */
505 if (hw->phy.media_type == ixgbe_media_type_fiber_qsfp)
506 *autoneg = FALSE;
507 else
508 *autoneg = TRUE;
509 }
510
511 out:
512 return status;
513 }
514
515 /**
516 * ixgbe_get_media_type_82599 - Get media type
517 * @hw: pointer to hardware structure
518 *
519 * Returns the media type (fiber, copper, backplane)
520 **/
521 enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw)
522 {
523 enum ixgbe_media_type media_type;
524
525 DEBUGFUNC("ixgbe_get_media_type_82599");
526
527 /* Detect if there is a copper PHY attached. */
528 switch (hw->phy.type) {
531 media_type = ixgbe_media_type_copper;
532 goto out;
533 default:
534 break;
535 }
536
537 switch (hw->device_id) {
538 case IXGBE_DEV_ID_82599_KX4:
539 case IXGBE_DEV_ID_82599_KX4_MEZZ:
540 case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
541 case IXGBE_DEV_ID_82599_KR:
542 case IXGBE_DEV_ID_82599_BACKPLANE_FCOE:
543 case IXGBE_DEV_ID_82599_XAUI_LOM:
544 /* Default device ID is mezzanine card KX/KX4 */
545 media_type = ixgbe_media_type_backplane;
546 break;
547 case IXGBE_DEV_ID_82599_SFP:
548 case IXGBE_DEV_ID_82599_SFP_FCOE:
549 case IXGBE_DEV_ID_82599_SFP_EM:
550 case IXGBE_DEV_ID_82599_SFP_SF2:
551 case IXGBE_DEV_ID_82599_SFP_SF_QP:
552 case IXGBE_DEV_ID_82599EN_SFP:
553 media_type = ixgbe_media_type_fiber;
554 break;
555 case IXGBE_DEV_ID_82599_CX4:
556 media_type = ixgbe_media_type_cx4;
557 break;
558 case IXGBE_DEV_ID_82599_T3_LOM:
559 media_type = ixgbe_media_type_copper;
560 break;
561 case IXGBE_DEV_ID_82599_QSFP_SF_QP:
562 media_type = ixgbe_media_type_fiber_qsfp;
563 break;
564 case IXGBE_DEV_ID_82599_BYPASS:
565 media_type = ixgbe_media_type_fiber_fixed;
566 hw->phy.multispeed_fiber = TRUE;
567 break;
568 default:
569 media_type = ixgbe_media_type_unknown;
570 break;
571 }
572 out:
573 return media_type;
574 }
575
576 /**
577 * ixgbe_stop_mac_link_on_d3_82599 - Disables link on D3
578 * @hw: pointer to hardware structure
579 *
580 * Disables link during D3 power down sequence.
581 *
582 **/
583 void ixgbe_stop_mac_link_on_d3_82599(struct ixgbe_hw *hw)
584 {
585 u32 autoc2_reg;
586 u16 ee_ctrl_2 = 0;
587
588 DEBUGFUNC("ixgbe_stop_mac_link_on_d3_82599");
589 ixgbe_read_eeprom(hw, IXGBE_EEPROM_CTRL_2, &ee_ctrl_2);
590
591 if (!ixgbe_mng_present(hw) && !hw->wol_enabled &&
592 ee_ctrl_2 & IXGBE_EEPROM_CCD_BIT) {
593 autoc2_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
594 autoc2_reg |= IXGBE_AUTOC2_LINK_DISABLE_ON_D3_MASK;
595 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2_reg);
596 }
597 }
598
599 /**
600 * ixgbe_start_mac_link_82599 - Setup MAC link settings
601 * @hw: pointer to hardware structure
602 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
603 *
604 * Configures link settings based on values in the ixgbe_hw struct.
605 * Restarts the link. Performs autonegotiation if needed.
606 **/
607 s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw,
608 bool autoneg_wait_to_complete)
609 {
610 u32 autoc_reg;
611 u32 links_reg;
612 u32 i;
613 s32 status = IXGBE_SUCCESS;
614 bool got_lock = FALSE;
615
616 DEBUGFUNC("ixgbe_start_mac_link_82599");
617
618
619 /* reset_pipeline requires us to hold this lock as it writes to
620 * AUTOC.
621 */
622 if (ixgbe_verify_lesm_fw_enabled_82599(hw)) {
623 status = hw->mac.ops.acquire_swfw_sync(hw,
624 IXGBE_GSSR_MAC_CSR_SM);
625 if (status != IXGBE_SUCCESS)
626 goto out;
627
628 got_lock = TRUE;
629 }
630
631 /* Restart link */
632 ixgbe_reset_pipeline_82599(hw);
633
634 if (got_lock)
635 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
636
637 /* Only poll for autoneg to complete if specified to do so */
638 if (autoneg_wait_to_complete) {
639 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
640 if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
641 IXGBE_AUTOC_LMS_KX4_KX_KR ||
642 (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
643 IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
644 (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
645 IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
646 links_reg = 0; /* Just in case Autoneg time = 0 */
647 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
648 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
649 if (links_reg & IXGBE_LINKS_KX_AN_COMP)
650 break;
651 msec_delay(100);
652 }
653 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
654 status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
655 DEBUGOUT("Autoneg did not complete.\n");
656 }
657 }
658 }
659
660 /* Add delay to filter out noises during initial link setup */
661 msec_delay(50);
662
663 out:
664 return status;
665 }
666
667 /**
668 * ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
669 * @hw: pointer to hardware structure
670 *
671 * The base drivers may require better control over SFP+ module
672 * PHY states. This includes selectively shutting down the Tx
673 * laser on the PHY, effectively halting physical link.
674 **/
675 void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
676 {
677 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
678
679 /* Blocked by MNG FW so bail */
680 if (ixgbe_check_reset_blocked(hw))
681 return;
682
683 /* Disable Tx laser; allow 100us to go dark per spec */
684 esdp_reg |= IXGBE_ESDP_SDP3;
685 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
686 IXGBE_WRITE_FLUSH(hw);
687 usec_delay(100);
688 }
689
690 /**
691 * ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
692 * @hw: pointer to hardware structure
693 *
694 * The base drivers may require better control over SFP+ module
695 * PHY states. This includes selectively turning on the Tx
696 * laser on the PHY, effectively starting physical link.
697 **/
698 void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
699 {
700 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
701
702 /* Enable Tx laser; allow 100ms to light up */
703 esdp_reg &= ~IXGBE_ESDP_SDP3;
704 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
705 IXGBE_WRITE_FLUSH(hw);
706 msec_delay(100);
707 }
708
709 /**
710 * ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
711 * @hw: pointer to hardware structure
712 *
713 * When the driver changes the link speeds that it can support,
714 * it sets autotry_restart to TRUE to indicate that we need to
715 * initiate a new autotry session with the link partner. To do
716 * so, we set the speed then disable and re-enable the Tx laser, to
717 * alert the link partner that it also needs to restart autotry on its
718 * end. This is consistent with TRUE clause 37 autoneg, which also
719 * involves a loss of signal.
720 **/
721 void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
722 {
723 DEBUGFUNC("ixgbe_flap_tx_laser_multispeed_fiber");
724
725 /* Blocked by MNG FW so bail */
726 if (ixgbe_check_reset_blocked(hw))
727 return;
728
729 if (hw->mac.autotry_restart) {
730 ixgbe_disable_tx_laser_multispeed_fiber(hw);
731 ixgbe_enable_tx_laser_multispeed_fiber(hw);
732 hw->mac.autotry_restart = FALSE;
733 }
734 }
735
736 /**
737 * ixgbe_set_hard_rate_select_speed - Set module link speed
738 * @hw: pointer to hardware structure
739 * @speed: link speed to set
740 *
741 * Set module link speed via RS0/RS1 rate select pins.
742 */
743 void ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *hw,
744 ixgbe_link_speed speed)
745 {
746 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
747
748 switch (speed) {
749 case IXGBE_LINK_SPEED_10GB_FULL:
750 esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
751 break;
752 case IXGBE_LINK_SPEED_1GB_FULL:
753 esdp_reg &= ~IXGBE_ESDP_SDP5;
754 esdp_reg |= IXGBE_ESDP_SDP5_DIR;
755 break;
756 default:
757 DEBUGOUT("Invalid fixed module speed\n");
758 return;
759 }
760
761 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
762 IXGBE_WRITE_FLUSH(hw);
763 }
764
765 /**
766 * ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed
767 * @hw: pointer to hardware structure
768 * @speed: new link speed
769 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
770 *
771 * Implements the Intel SmartSpeed algorithm.
772 **/
773 s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
774 ixgbe_link_speed speed,
775 bool autoneg_wait_to_complete)
776 {
777 s32 status = IXGBE_SUCCESS;
778 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
779 s32 i, j;
780 bool link_up = FALSE;
781 u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
782
783 DEBUGFUNC("ixgbe_setup_mac_link_smartspeed");
784
785 /* Set autoneg_advertised value based on input link speed */
786 hw->phy.autoneg_advertised = 0;
787
788 if (speed & IXGBE_LINK_SPEED_10GB_FULL)
789 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
790
791 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
792 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
793
794 if (speed & IXGBE_LINK_SPEED_100_FULL)
795 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL;
796
797 /*
798 * Implement Intel SmartSpeed algorithm. SmartSpeed will reduce the
799 * autoneg advertisement if link is unable to be established at the
800 * highest negotiated rate. This can sometimes happen due to integrity
801 * issues with the physical media connection.
802 */
803
804 /* First, try to get link with full advertisement */
805 hw->phy.smart_speed_active = FALSE;
806 for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) {
807 status = ixgbe_setup_mac_link_82599(hw, speed,
808 autoneg_wait_to_complete);
809 if (status != IXGBE_SUCCESS)
810 goto out;
811
812 /*
813 * Wait for the controller to acquire link. Per IEEE 802.3ap,
814 * Section 73.10.2, we may have to wait up to 500ms if KR is
815 * attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per
816 * Table 9 in the AN MAS.
817 */
818 for (i = 0; i < 5; i++) {
819 msec_delay(100);
820
821 /* If we have link, just jump out */
822 status = ixgbe_check_link(hw, &link_speed, &link_up,
823 FALSE);
824 if (status != IXGBE_SUCCESS)
825 goto out;
826
827 if (link_up)
828 goto out;
829 }
830 }
831
832 /*
833 * We didn't get link. If we advertised KR plus one of KX4/KX
834 * (or BX4/BX), then disable KR and try again.
835 */
836 if (((autoc_reg & IXGBE_AUTOC_KR_SUPP) == 0) ||
837 ((autoc_reg & IXGBE_AUTOC_KX4_KX_SUPP_MASK) == 0))
838 goto out;
839
840 /* Turn SmartSpeed on to disable KR support */
841 hw->phy.smart_speed_active = TRUE;
842 status = ixgbe_setup_mac_link_82599(hw, speed,
843 autoneg_wait_to_complete);
844 if (status != IXGBE_SUCCESS)
845 goto out;
846
847 /*
848 * Wait for the controller to acquire link. 600ms will allow for
849 * the AN link_fail_inhibit_timer as well for multiple cycles of
850 * parallel detect, both 10g and 1g. This allows for the maximum
851 * connect attempts as defined in the AN MAS table 73-7.
852 */
853 for (i = 0; i < 6; i++) {
854 msec_delay(100);
855
856 /* If we have link, just jump out */
857 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE);
858 if (status != IXGBE_SUCCESS)
859 goto out;
860
861 if (link_up)
862 goto out;
863 }
864
865 /* We didn't get link. Turn SmartSpeed back off. */
866 hw->phy.smart_speed_active = FALSE;
867 status = ixgbe_setup_mac_link_82599(hw, speed,
868 autoneg_wait_to_complete);
869
870 out:
871 if (link_up && (link_speed == IXGBE_LINK_SPEED_1GB_FULL))
872 DEBUGOUT("Smartspeed has downgraded the link speed "
873 "from the maximum advertised\n");
874 return status;
875 }
876
877 /**
878 * ixgbe_setup_mac_link_82599 - Set MAC link speed
879 * @hw: pointer to hardware structure
880 * @speed: new link speed
881 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed
882 *
883 * Set the link speed in the AUTOC register and restarts link.
884 **/
885 s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
886 ixgbe_link_speed speed,
887 bool autoneg_wait_to_complete)
888 {
889 bool autoneg = FALSE;
890 s32 status = IXGBE_SUCCESS;
891 u32 pma_pmd_1g, link_mode;
892 u32 current_autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); /* holds the value of AUTOC register at this current point in time */
893 u32 orig_autoc = 0; /* holds the cached value of AUTOC register */
894 u32 autoc = current_autoc; /* Temporary variable used for comparison purposes */
895 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
896 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
897 u32 links_reg;
898 u32 i;
899 ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN;
900
901 DEBUGFUNC("ixgbe_setup_mac_link_82599");
902
903 /* Check to see if speed passed in is supported. */
904 status = ixgbe_get_link_capabilities(hw, &link_capabilities, &autoneg);
905 if (status)
906 goto out;
907
908 speed &= link_capabilities;
909
910 if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
911 status = IXGBE_ERR_LINK_SETUP;
912 goto out;
913 }
914
915 /* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/
916 if (hw->mac.orig_link_settings_stored)
917 orig_autoc = hw->mac.orig_autoc;
918 else
919 orig_autoc = autoc;
920
921 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
922 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
923
924 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
925 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
926 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
927 /* Set KX4/KX/KR support according to speed requested */
928 autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP);
929 if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
930 if (orig_autoc & IXGBE_AUTOC_KX4_SUPP)
931 autoc |= IXGBE_AUTOC_KX4_SUPP;
932 if ((orig_autoc & IXGBE_AUTOC_KR_SUPP) &&
933 (hw->phy.smart_speed_active == FALSE))
934 autoc |= IXGBE_AUTOC_KR_SUPP;
935 }
936 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
937 autoc |= IXGBE_AUTOC_KX_SUPP;
938 } else if ((pma_pmd_1g == IXGBE_AUTOC_1G_SFI) &&
939 (link_mode == IXGBE_AUTOC_LMS_1G_LINK_NO_AN ||
940 link_mode == IXGBE_AUTOC_LMS_1G_AN)) {
941 /* Switch from 1G SFI to 10G SFI if requested */
942 if ((speed == IXGBE_LINK_SPEED_10GB_FULL) &&
943 (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)) {
944 autoc &= ~IXGBE_AUTOC_LMS_MASK;
945 autoc |= IXGBE_AUTOC_LMS_10G_SERIAL;
946 }
947 } else if ((pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) &&
948 (link_mode == IXGBE_AUTOC_LMS_10G_SERIAL)) {
949 /* Switch from 10G SFI to 1G SFI if requested */
950 if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
951 (pma_pmd_1g == IXGBE_AUTOC_1G_SFI)) {
952 autoc &= ~IXGBE_AUTOC_LMS_MASK;
953 if (autoneg || hw->phy.type == ixgbe_phy_qsfp_intel)
954 autoc |= IXGBE_AUTOC_LMS_1G_AN;
955 else
956 autoc |= IXGBE_AUTOC_LMS_1G_LINK_NO_AN;
957 }
958 }
959
960 if (autoc != current_autoc) {
961 /* Restart link */
962 status = hw->mac.ops.prot_autoc_write(hw, autoc, FALSE);
963 if (status != IXGBE_SUCCESS)
964 goto out;
965
966 /* Only poll for autoneg to complete if specified to do so */
967 if (autoneg_wait_to_complete) {
968 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
969 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
970 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
971 links_reg = 0; /*Just in case Autoneg time=0*/
972 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
973 links_reg =
974 IXGBE_READ_REG(hw, IXGBE_LINKS);
975 if (links_reg & IXGBE_LINKS_KX_AN_COMP)
976 break;
977 msec_delay(100);
978 }
979 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
980 status =
981 IXGBE_ERR_AUTONEG_NOT_COMPLETE;
982 DEBUGOUT("Autoneg did not complete.\n");
983 }
984 }
985 }
986
987 /* Add delay to filter out noises during initial link setup */
988 msec_delay(50);
989 }
990
991 out:
992 return status;
993 }
994
995 /**
996 * ixgbe_setup_copper_link_82599 - Set the PHY autoneg advertised field
997 * @hw: pointer to hardware structure
998 * @speed: new link speed
999 * @autoneg_wait_to_complete: TRUE if waiting is needed to complete
1000 *
1001 * Restarts link on PHY and MAC based on settings passed in.
1002 **/
1003 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
1004 ixgbe_link_speed speed,
1005 bool autoneg_wait_to_complete)
1006 {
1007 s32 status;
1008
1009 DEBUGFUNC("ixgbe_setup_copper_link_82599");
1010
1011 /* Setup the PHY according to input speed */
1012 status = hw->phy.ops.setup_link_speed(hw, speed,
1013 autoneg_wait_to_complete);
1014 /* Set up MAC */
1015 ixgbe_start_mac_link_82599(hw, autoneg_wait_to_complete);
1016
1017 return status;
1018 }
1019
1020 /**
1021 * ixgbe_reset_hw_82599 - Perform hardware reset
1022 * @hw: pointer to hardware structure
1023 *
1024 * Resets the hardware by resetting the transmit and receive units, masks
1025 * and clears all interrupts, perform a PHY reset, and perform a link (MAC)
1026 * reset.
1027 **/
1028 s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
1029 {
1030 ixgbe_link_speed link_speed;
1031 s32 status;
1032 u32 ctrl = 0;
1033 u32 i, autoc, autoc2;
1034 u32 curr_lms;
1035 bool link_up = FALSE;
1036
1037 DEBUGFUNC("ixgbe_reset_hw_82599");
1038
1039 /* Call adapter stop to disable tx/rx and clear interrupts */
1040 status = hw->mac.ops.stop_adapter(hw);
1041 if (status != IXGBE_SUCCESS)
1042 goto reset_hw_out;
1043
1044 /* flush pending Tx transactions */
1045 ixgbe_clear_tx_pending(hw);
1046
1047 /* PHY ops must be identified and initialized prior to reset */
1048
1049 /* Identify PHY and related function pointers */
1050 status = hw->phy.ops.init(hw);
1051
1052 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
1053 goto reset_hw_out;
1054
1055 /* Setup SFP module if there is one present. */
1056 if (hw->phy.sfp_setup_needed) {
1057 status = hw->mac.ops.setup_sfp(hw);
1058 hw->phy.sfp_setup_needed = FALSE;
1059 }
1060
1061 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
1062 goto reset_hw_out;
1063
1064 /* Reset PHY */
1065 if (hw->phy.reset_disable == FALSE && hw->phy.ops.reset != NULL)
1066 hw->phy.ops.reset(hw);
1067
1068 /* remember AUTOC from before we reset */
1069 curr_lms = IXGBE_READ_REG(hw, IXGBE_AUTOC) & IXGBE_AUTOC_LMS_MASK;
1070
1071 mac_reset_top:
1072 /*
1073 * Issue global reset to the MAC. Needs to be SW reset if link is up.
1074 * If link reset is used when link is up, it might reset the PHY when
1075 * mng is using it. If link is down or the flag to force full link
1076 * reset is set, then perform link reset.
1077 */
1078 ctrl = IXGBE_CTRL_LNK_RST;
1079 if (!hw->force_full_reset) {
1080 hw->mac.ops.check_link(hw, &link_speed, &link_up, FALSE);
1081 if (link_up)
1082 ctrl = IXGBE_CTRL_RST;
1083 }
1084
1085 ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
1086 IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl);
1087 IXGBE_WRITE_FLUSH(hw);
1088
1089 /* Poll for reset bit to self-clear meaning reset is complete */
1090 for (i = 0; i < 10; i++) {
1091 usec_delay(1);
1092 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
1093 if (!(ctrl & IXGBE_CTRL_RST_MASK))
1094 break;
1095 }
1096
1097 if (ctrl & IXGBE_CTRL_RST_MASK) {
1098 status = IXGBE_ERR_RESET_FAILED;
1099 DEBUGOUT("Reset polling failed to complete.\n");
1100 }
1101
1102 msec_delay(50);
1103
1104 /*
1105 * Double resets are required for recovery from certain error
1106 * conditions. Between resets, it is necessary to stall to
1107 * allow time for any pending HW events to complete.
1108 */
1109 if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) {
1110 hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
1111 goto mac_reset_top;
1112 }
1113
1114 /*
1115 * Store the original AUTOC/AUTOC2 values if they have not been
1116 * stored off yet. Otherwise restore the stored original
1117 * values since the reset operation sets back to defaults.
1118 */
1119 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
1120 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
1121
1122 /* Enable link if disabled in NVM */
1123 if (autoc2 & IXGBE_AUTOC2_LINK_DISABLE_MASK) {
1124 autoc2 &= ~IXGBE_AUTOC2_LINK_DISABLE_MASK;
1125 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2);
1126 IXGBE_WRITE_FLUSH(hw);
1127 }
1128
1129 if (hw->mac.orig_link_settings_stored == FALSE) {
1130 hw->mac.orig_autoc = autoc;
1131 hw->mac.orig_autoc2 = autoc2;
1132 hw->mac.orig_link_settings_stored = TRUE;
1133 } else {
1134
1135 /* If MNG FW is running on a multi-speed device that
1136 * doesn't autoneg with out driver support we need to
1137 * leave LMS in the state it was before we MAC reset.
1138 * Likewise if we support WoL we don't want change the
1139 * LMS state.
1140 */
1141 if ((hw->phy.multispeed_fiber && ixgbe_mng_enabled(hw)) ||
1142 hw->wol_enabled)
1143 hw->mac.orig_autoc =
1144 (hw->mac.orig_autoc & ~IXGBE_AUTOC_LMS_MASK) |
1145 curr_lms;
1146
1147 if (autoc != hw->mac.orig_autoc) {
1148 status = hw->mac.ops.prot_autoc_write(hw,
1149 hw->mac.orig_autoc,
1150 FALSE);
1151 if (status != IXGBE_SUCCESS)
1152 goto reset_hw_out;
1153 }
1154
1155 if ((autoc2 & IXGBE_AUTOC2_UPPER_MASK) !=
1156 (hw->mac.orig_autoc2 & IXGBE_AUTOC2_UPPER_MASK)) {
1157 autoc2 &= ~IXGBE_AUTOC2_UPPER_MASK;
1158 autoc2 |= (hw->mac.orig_autoc2 &
1159 IXGBE_AUTOC2_UPPER_MASK);
1160 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2);
1161 }
1162 }
1163
1164 /* Store the permanent mac address */
1165 hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
1166
1167 /*
1168 * Store MAC address from RAR0, clear receive address registers, and
1169 * clear the multicast table. Also reset num_rar_entries to 128,
1170 * since we modify this value when programming the SAN MAC address.
1171 */
1172 hw->mac.num_rar_entries = 128;
1173 hw->mac.ops.init_rx_addrs(hw);
1174
1179 if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
1180 hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
1181 hw->mac.san_addr, 0, IXGBE_RAH_AV);
1182
1183 /* Save the SAN MAC RAR index */
1184 hw->mac.san_mac_rar_index = hw->mac.num_rar_entries - 1;
1185
1186 /* Reserve the last RAR for the SAN MAC address */
1187 hw->mac.num_rar_entries--;
1188 }
1189
1190 /* Store the alternative WWNN/WWPN prefix */
1191 hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix,
1192 &hw->mac.wwpn_prefix);
1193
1194 reset_hw_out:
1195 return status;
1196 }
1197
1198 /**
1199 * ixgbe_fdir_check_cmd_complete - poll to check whether FDIRCMD is complete
1200 * @hw: pointer to hardware structure
1201 * @fdircmd: current value of FDIRCMD register
1202 */
1203 static s32 ixgbe_fdir_check_cmd_complete(struct ixgbe_hw *hw, u32 *fdircmd)
1204 {
1205 int i;
1206
1207 for (i = 0; i < IXGBE_FDIRCMD_CMD_POLL; i++) {
1208 *fdircmd = IXGBE_READ_REG(hw, IXGBE_FDIRCMD);
1209 if (!(*fdircmd & IXGBE_FDIRCMD_CMD_MASK))
1210 return IXGBE_SUCCESS;
1211 usec_delay(10);
1212 }
1213
1214 return IXGBE_ERR_FDIR_CMD_INCOMPLETE;
1215 }
1216
1217 /**
1218 * ixgbe_reinit_fdir_tables_82599 - Reinitialize Flow Director tables.
1219 * @hw: pointer to hardware structure
1220 **/
1221 s32 ixgbe_reinit_fdir_tables_82599(struct ixgbe_hw *hw)
1222 {
1223 s32 err;
1224 int i;
1225 u32 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL);
1226 u32 fdircmd;
1227 fdirctrl &= ~IXGBE_FDIRCTRL_INIT_DONE;
1228
1229 DEBUGFUNC("ixgbe_reinit_fdir_tables_82599");
1230
1231 /*
1232 * Before starting reinitialization process,
1233 * FDIRCMD.CMD must be zero.
1234 */
1235 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd);
1236 if (err) {
1237 DEBUGOUT("Flow Director previous command did not complete, aborting table re-initialization.\n");
1238 return err;
1239 }
1240
1241 IXGBE_WRITE_REG(hw, IXGBE_FDIRFREE, 0);
1242 IXGBE_WRITE_FLUSH(hw);
1243 /*
1244 * 82599 adapters flow director init flow cannot be restarted,
1245 * Workaround 82599 silicon errata by performing the following steps
1246 * before re-writing the FDIRCTRL control register with the same value.
1247 * - write 1 to bit 8 of FDIRCMD register &
1248 * - write 0 to bit 8 of FDIRCMD register
1249 */
1250 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1251 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) |
1252 IXGBE_FDIRCMD_CLEARHT));
1253 IXGBE_WRITE_FLUSH(hw);
1254 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1255 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
1256 ~IXGBE_FDIRCMD_CLEARHT));
1257 IXGBE_WRITE_FLUSH(hw);
1258 /*
1259 * Clear FDIR Hash register to clear any leftover hashes
1260 * waiting to be programmed.
1261 */
1262 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, 0x00);
1263 IXGBE_WRITE_FLUSH(hw);
1264
1265 IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl);
1266 IXGBE_WRITE_FLUSH(hw);
1267
1268 /* Poll init-done after we write FDIRCTRL register */
1269 for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) {
1270 if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) &
1271 IXGBE_FDIRCTRL_INIT_DONE)
1272 break;
1273 msec_delay(1);
1274 }
1275 if (i >= IXGBE_FDIR_INIT_DONE_POLL) {
1276 DEBUGOUT("Flow Director Signature poll time exceeded!\n");
1277 return IXGBE_ERR_FDIR_REINIT_FAILED;
1278 }
1279
1280 /* Clear FDIR statistics registers (read to clear) */
1281 IXGBE_READ_REG(hw, IXGBE_FDIRUSTAT);
1282 IXGBE_READ_REG(hw, IXGBE_FDIRFSTAT);
1283 IXGBE_READ_REG(hw, IXGBE_FDIRMATCH);
1284 IXGBE_READ_REG(hw, IXGBE_FDIRMISS);
1285 IXGBE_READ_REG(hw, IXGBE_FDIRLEN);
1286
1287 return IXGBE_SUCCESS;
1288 }
1289
1290 /**
1291 * ixgbe_fdir_enable_82599 - Initialize Flow Director control registers
1292 * @hw: pointer to hardware structure
1293 * @fdirctrl: value to write to flow director control register
1294 **/
1295 static void ixgbe_fdir_enable_82599(struct ixgbe_hw *hw, u32 fdirctrl)
1296 {
1297 int i;
1298
1299 DEBUGFUNC("ixgbe_fdir_enable_82599");
1300
1301 /* Prime the keys for hashing */
1302 IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY, IXGBE_ATR_BUCKET_HASH_KEY);
1303 IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY, IXGBE_ATR_SIGNATURE_HASH_KEY);
1304
1305 /*
1342 * Continue setup of fdirctrl register bits:
1343 * Move the flexible bytes to use the ethertype - shift 6 words
1344 * Set the maximum length per hash bucket to 0xA filters
1345 * Send interrupt when 64 filters are left
1346 */
1347 fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) |
1348 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) |
1349 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT);
1350
1351 /* write hashes and fdirctrl register, poll for completion */
1352 ixgbe_fdir_enable_82599(hw, fdirctrl);
1353
1354 return IXGBE_SUCCESS;
1355 }
1356
1357 /**
1358 * ixgbe_init_fdir_perfect_82599 - Initialize Flow Director perfect filters
1359 * @hw: pointer to hardware structure
1360 * @fdirctrl: value to write to flow director control register, initially
1361 * contains just the value of the Rx packet buffer allocation
1362 * @cloud_mode: TRUE - cloud mode, FALSE - other mode
1363 **/
1364 s32 ixgbe_init_fdir_perfect_82599(struct ixgbe_hw *hw, u32 fdirctrl,
1365 bool cloud_mode)
1366 {
1367 DEBUGFUNC("ixgbe_init_fdir_perfect_82599");
1368
1369 /*
1370 * Continue setup of fdirctrl register bits:
1371 * Turn perfect match filtering on
1372 * Report hash in RSS field of Rx wb descriptor
1373 * Initialize the drop queue to queue 127
1374 * Move the flexible bytes to use the ethertype - shift 6 words
1375 * Set the maximum length per hash bucket to 0xA filters
1376 * Send interrupt when 64 (0x4 * 16) filters are left
1377 */
1378 fdirctrl |= IXGBE_FDIRCTRL_PERFECT_MATCH |
1379 IXGBE_FDIRCTRL_REPORT_STATUS |
1380 (IXGBE_FDIR_DROP_QUEUE << IXGBE_FDIRCTRL_DROP_Q_SHIFT) |
1381 (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) |
1382 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) |
1383 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT);
1384 if ((hw->mac.type == ixgbe_mac_X550) ||
1385 (hw->mac.type == ixgbe_mac_X550EM_x))
1386 fdirctrl |= IXGBE_FDIRCTRL_DROP_NO_MATCH;
1387
1388 if (cloud_mode)
1389 fdirctrl |=(IXGBE_FDIRCTRL_FILTERMODE_CLOUD <<
1390 IXGBE_FDIRCTRL_FILTERMODE_SHIFT);
1391
1392 /* write hashes and fdirctrl register, poll for completion */
1393 ixgbe_fdir_enable_82599(hw, fdirctrl);
1394
1395 return IXGBE_SUCCESS;
1396 }
1397
1398 /**
1399 * ixgbe_set_fdir_drop_queue_82599 - Set Flow Director drop queue
1400 * @hw: pointer to hardware structure
1401 * @dropqueue: Rx queue index used for the dropped packets
1402 **/
1403 void ixgbe_set_fdir_drop_queue_82599(struct ixgbe_hw *hw, u8 dropqueue)
1404 {
1405 u32 fdirctrl;
1406
1407 DEBUGFUNC("ixgbe_set_fdir_drop_queue_82599");
1408 /* Clear init done bit and drop queue field */
1409 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL);
1410 fdirctrl &= ~(IXGBE_FDIRCTRL_DROP_Q_MASK | IXGBE_FDIRCTRL_INIT_DONE);
1411
1412 /* Set drop queue */
1413 fdirctrl |= (dropqueue << IXGBE_FDIRCTRL_DROP_Q_SHIFT);
1414 if ((hw->mac.type == ixgbe_mac_X550) ||
1415 (hw->mac.type == ixgbe_mac_X550EM_x))
1416 fdirctrl |= IXGBE_FDIRCTRL_DROP_NO_MATCH;
1417
1418 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1419 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) |
1420 IXGBE_FDIRCMD_CLEARHT));
1421 IXGBE_WRITE_FLUSH(hw);
1422 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1423 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
1424 ~IXGBE_FDIRCMD_CLEARHT));
1425 IXGBE_WRITE_FLUSH(hw);
1426
1427 /* write hashes and fdirctrl register, poll for completion */
1428 ixgbe_fdir_enable_82599(hw, fdirctrl);
1429 }
1430
1431 /*
1432 * These defines allow us to quickly generate all of the necessary instructions
1433 * in the function below by simply calling out IXGBE_COMPUTE_SIG_HASH_ITERATION
1434 * for values 0 through 15
1435 */
1436 #define IXGBE_ATR_COMMON_HASH_KEY \
1437 (IXGBE_ATR_BUCKET_HASH_KEY & IXGBE_ATR_SIGNATURE_HASH_KEY)
1438 #define IXGBE_COMPUTE_SIG_HASH_ITERATION(_n) \
1439 do { \
1440 u32 n = (_n); \
1441 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << n)) \
1442 common_hash ^= lo_hash_dword >> n; \
1443 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \
1444 bucket_hash ^= lo_hash_dword >> n; \
1445 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << n)) \
1446 sig_hash ^= lo_hash_dword << (16 - n); \
1447 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << (n + 16))) \
1448 common_hash ^= hi_hash_dword >> n; \
1449 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \
1450 bucket_hash ^= hi_hash_dword >> n; \
1451 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << (n + 16))) \
1452 sig_hash ^= hi_hash_dword << (16 - n); \
1453 } while (0)
1454
1455 /**
1456 * ixgbe_atr_compute_sig_hash_82599 - Compute the signature hash
1457 * @stream: input bitstream to compute the hash on
1458 *
1459 * This function is almost identical to the function above but contains
1460 * several optimizations such as unwinding all of the loops, letting the
1461 * compiler work out all of the conditional ifs since the keys are static
1462 * defines, and computing two keys at once since the hashed dword stream
1463 * will be the same for both keys.
1464 **/
1465 u32 ixgbe_atr_compute_sig_hash_82599(union ixgbe_atr_hash_dword input,
1466 union ixgbe_atr_hash_dword common)
1467 {
1468 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan;
1469 u32 sig_hash = 0, bucket_hash = 0, common_hash = 0;
1470
1471 /* record the flow_vm_vlan bits as they are a key part to the hash */
1472 flow_vm_vlan = IXGBE_NTOHL(input.dword);
1473
1474 /* generate common hash dword */
1475 hi_hash_dword = IXGBE_NTOHL(common.dword);
1476
1477 /* low dword is word swapped version of common */
1478 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16);
1479
1480 /* apply flow ID/VM pool/VLAN ID bits to hash words */
1481 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16);
1482
1483 /* Process bits 0 and 16 */
1484 IXGBE_COMPUTE_SIG_HASH_ITERATION(0);
1485
1486 /*
1487 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to
1488 * delay this because bit 0 of the stream should not be processed
1489 * so we do not add the VLAN until after bit 0 was processed
1490 */
1491 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16);
1492
1493 /* Process remaining 30 bit of the key */
1494 IXGBE_COMPUTE_SIG_HASH_ITERATION(1);
1495 IXGBE_COMPUTE_SIG_HASH_ITERATION(2);
1496 IXGBE_COMPUTE_SIG_HASH_ITERATION(3);
1497 IXGBE_COMPUTE_SIG_HASH_ITERATION(4);
1498 IXGBE_COMPUTE_SIG_HASH_ITERATION(5);
1499 IXGBE_COMPUTE_SIG_HASH_ITERATION(6);
1500 IXGBE_COMPUTE_SIG_HASH_ITERATION(7);
1501 IXGBE_COMPUTE_SIG_HASH_ITERATION(8);
1502 IXGBE_COMPUTE_SIG_HASH_ITERATION(9);
1503 IXGBE_COMPUTE_SIG_HASH_ITERATION(10);
1504 IXGBE_COMPUTE_SIG_HASH_ITERATION(11);
1505 IXGBE_COMPUTE_SIG_HASH_ITERATION(12);
1506 IXGBE_COMPUTE_SIG_HASH_ITERATION(13);
1507 IXGBE_COMPUTE_SIG_HASH_ITERATION(14);
1508 IXGBE_COMPUTE_SIG_HASH_ITERATION(15);
1509
1510 /* combine common_hash result with signature and bucket hashes */
1511 bucket_hash ^= common_hash;
1512 bucket_hash &= IXGBE_ATR_HASH_MASK;
1513
1514 sig_hash ^= common_hash << 16;
1515 sig_hash &= IXGBE_ATR_HASH_MASK << 16;
1516
1517 /* return completed signature hash */
1518 return sig_hash ^ bucket_hash;
1519 }
1520
1521 /**
1522 * ixgbe_atr_add_signature_filter_82599 - Adds a signature hash filter
1523 * @hw: pointer to hardware structure
1524 * @input: unique input dword
1525 * @common: compressed common input dword
1526 * @queue: queue index to direct traffic to
1527 *
1528 * Note that the tunnel bit in input must not be set when the hardware
1529 * tunneling support does not exist.
1530 **/
1531 void ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw,
1532 union ixgbe_atr_hash_dword input,
1533 union ixgbe_atr_hash_dword common,
1534 u8 queue)
1535 {
1536 u64 fdirhashcmd;
1537 u8 flow_type;
1538 bool tunnel;
1539 u32 fdircmd;
1540
1541 DEBUGFUNC("ixgbe_fdir_add_signature_filter_82599");
1542
1543 /*
1544 * Get the flow_type in order to program FDIRCMD properly
1545 * lowest 2 bits are FDIRCMD.L4TYPE, third lowest bit is FDIRCMD.IPV6
1546 * fifth is FDIRCMD.TUNNEL_FILTER
1547 */
1548 tunnel = !!(input.formatted.flow_type & IXGBE_ATR_L4TYPE_TUNNEL_MASK);
1549 flow_type = input.formatted.flow_type &
1550 (IXGBE_ATR_L4TYPE_TUNNEL_MASK - 1);
1551 switch (flow_type) {
1552 case IXGBE_ATR_FLOW_TYPE_TCPV4:
1553 case IXGBE_ATR_FLOW_TYPE_UDPV4:
1554 case IXGBE_ATR_FLOW_TYPE_SCTPV4:
1555 case IXGBE_ATR_FLOW_TYPE_TCPV6:
1556 case IXGBE_ATR_FLOW_TYPE_UDPV6:
1557 case IXGBE_ATR_FLOW_TYPE_SCTPV6:
1558 break;
1559 default:
1560 DEBUGOUT(" Error on flow type input\n");
1561 return;
1562 }
1563
1564 /* configure FDIRCMD register */
1565 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE |
1566 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN;
1567 fdircmd |= (u32)flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT;
1568 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT;
1569 if (tunnel)
1570 fdircmd |= IXGBE_FDIRCMD_TUNNEL_FILTER;
1571
1572 /*
1573 * The lower 32-bits of fdirhashcmd is for FDIRHASH, the upper 32-bits
1574 * is for FDIRCMD. Then do a 64-bit register write from FDIRHASH.
1575 */
1576 fdirhashcmd = (u64)fdircmd << 32;
1577 fdirhashcmd |= ixgbe_atr_compute_sig_hash_82599(input, common);
1578 IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd);
1579
1580 DEBUGOUT2("Tx Queue=%x hash=%x\n", queue, (u32)fdirhashcmd);
1581
1582 return;
1583 }
1584
1585 #define IXGBE_COMPUTE_BKT_HASH_ITERATION(_n) \
1586 do { \
1587 u32 n = (_n); \
1588 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \
1589 bucket_hash ^= lo_hash_dword >> n; \
1590 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \
1591 bucket_hash ^= hi_hash_dword >> n; \
1592 } while (0)
1593
1594 /**
1595 * ixgbe_atr_compute_perfect_hash_82599 - Compute the perfect filter hash
1596 * @atr_input: input bitstream to compute the hash on
1597 * @input_mask: mask for the input bitstream
1598 *
1599 * This function serves two main purposes. First it applies the input_mask
1600 * to the atr_input resulting in a cleaned up atr_input data stream.
1601 * Secondly it computes the hash and stores it in the bkt_hash field at
1602 * the end of the input byte stream. This way it will be available for
1603 * future use without needing to recompute the hash.
1604 **/
1605 void ixgbe_atr_compute_perfect_hash_82599(union ixgbe_atr_input *input,
1606 union ixgbe_atr_input *input_mask)
1607 {
1608
1609 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan;
1610 u32 bucket_hash = 0;
1611 u32 hi_dword = 0;
1612 u32 i = 0;
1613
1614 /* Apply masks to input data */
1615 for (i = 0; i < 14; i++)
1616 input->dword_stream[i] &= input_mask->dword_stream[i];
1617
1618 /* record the flow_vm_vlan bits as they are a key part to the hash */
1619 flow_vm_vlan = IXGBE_NTOHL(input->dword_stream[0]);
1620
1621 /* generate common hash dword */
1622 for (i = 1; i <= 13; i++)
1623 hi_dword ^= input->dword_stream[i];
1624 hi_hash_dword = IXGBE_NTOHL(hi_dword);
1625
1626 /* low dword is word swapped version of common */
1627 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16);
1628
1629 /* apply flow ID/VM pool/VLAN ID bits to hash words */
1630 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16);
1631
1632 /* Process bits 0 and 16 */
1633 IXGBE_COMPUTE_BKT_HASH_ITERATION(0);
1634
1635 /*
1636 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to
1637 * delay this because bit 0 of the stream should not be processed
1638 * so we do not add the VLAN until after bit 0 was processed
1639 */
1640 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16);
1641
1642 /* Process remaining 30 bit of the key */
1643 for (i = 1; i <= 15; i++)
1644 IXGBE_COMPUTE_BKT_HASH_ITERATION(i);
1645
1646 /*
1647 * Limit hash to 13 bits since max bucket count is 8K.
1648 * Store result at the end of the input stream.
1649 */
1650 input->formatted.bkt_hash = bucket_hash & 0x1FFF;
1651 }
1652
1653 /**
1654 * ixgbe_get_fdirtcpm_82599 - generate a TCP port from atr_input_masks
1655 * @input_mask: mask to be bit swapped
1656 *
1657 * The source and destination port masks for flow director are bit swapped
1658 * in that bit 15 effects bit 0, 14 effects 1, 13, 2 etc. In order to
1659 * generate a correctly swapped value we need to bit swap the mask and that
1660 * is what is accomplished by this function.
1661 **/
1662 static u32 ixgbe_get_fdirtcpm_82599(union ixgbe_atr_input *input_mask)
1663 {
1664 u32 mask = IXGBE_NTOHS(input_mask->formatted.dst_port);
1665 mask <<= IXGBE_FDIRTCPM_DPORTM_SHIFT;
1666 mask |= IXGBE_NTOHS(input_mask->formatted.src_port);
1667 mask = ((mask & 0x55555555) << 1) | ((mask & 0xAAAAAAAA) >> 1);
1668 mask = ((mask & 0x33333333) << 2) | ((mask & 0xCCCCCCCC) >> 2);
1669 mask = ((mask & 0x0F0F0F0F) << 4) | ((mask & 0xF0F0F0F0) >> 4);
1670 return ((mask & 0x00FF00FF) << 8) | ((mask & 0xFF00FF00) >> 8);
1671 }
1672
1673 /*
1674 * These two macros are meant to address the fact that we have registers
1675 * that are either all or in part big-endian. As a result on big-endian
1676 * systems we will end up byte swapping the value to little-endian before
1677 * it is byte swapped again and written to the hardware in the original
1678 * big-endian format.
1679 */
1680 #define IXGBE_STORE_AS_BE32(_value) \
1681 (((u32)(_value) >> 24) | (((u32)(_value) & 0x00FF0000) >> 8) | \
1682 (((u32)(_value) & 0x0000FF00) << 8) | ((u32)(_value) << 24))
1683
1684 #define IXGBE_WRITE_REG_BE32(a, reg, value) \
1685 IXGBE_WRITE_REG((a), (reg), IXGBE_STORE_AS_BE32(IXGBE_NTOHL(value)))
1686
1687 #define IXGBE_STORE_AS_BE16(_value) \
1688 IXGBE_NTOHS(((u16)(_value) >> 8) | ((u16)(_value) << 8))
1689
1690 s32 ixgbe_fdir_set_input_mask_82599(struct ixgbe_hw *hw,
1691 union ixgbe_atr_input *input_mask, bool cloud_mode)
1692 {
1693 /* mask IPv6 since it is currently not supported */
1694 u32 fdirm = IXGBE_FDIRM_DIPv6;
1695 u32 fdirtcpm;
1696 u32 fdirip6m;
1697 DEBUGFUNC("ixgbe_fdir_set_atr_input_mask_82599");
1698
1699 /*
1700 * Program the relevant mask registers. If src/dst_port or src/dst_addr
1701 * are zero, then assume a full mask for that field. Also assume that
1702 * a VLAN of 0 is unspecified, so mask that out as well. L4type
1703 * cannot be masked out in this implementation.
1704 *
1705 * This also assumes IPv4 only. IPv6 masking isn't supported at this
1706 * point in time.
1707 */
1708
1709 /* verify bucket hash is cleared on hash generation */
1710 if (input_mask->formatted.bkt_hash)
1711 DEBUGOUT(" bucket hash should always be 0 in mask\n");
1712
1713 /* Program FDIRM and verify partial masks */
1714 switch (input_mask->formatted.vm_pool & 0x7F) {
1715 case 0x0:
1716 fdirm |= IXGBE_FDIRM_POOL;
1717 case 0x7F:
1718 break;
1719 default:
1720 DEBUGOUT(" Error on vm pool mask\n");
1721 return IXGBE_ERR_CONFIG;
1722 }
1723
1724 switch (input_mask->formatted.flow_type & IXGBE_ATR_L4TYPE_MASK) {
1725 case 0x0:
1726 fdirm |= IXGBE_FDIRM_L4P;
1727 if (input_mask->formatted.dst_port ||
1728 input_mask->formatted.src_port) {
1729 DEBUGOUT(" Error on src/dst port mask\n");
1730 return IXGBE_ERR_CONFIG;
1731 }
1732 case IXGBE_ATR_L4TYPE_MASK:
1733 break;
1734 default:
1735 DEBUGOUT(" Error on flow type mask\n");
1736 return IXGBE_ERR_CONFIG;
1737 }
1738
1739 switch (IXGBE_NTOHS(input_mask->formatted.vlan_id) & 0xEFFF) {
1740 case 0x0000:
1741 /* mask VLAN ID, fall through to mask VLAN priority */
1742 fdirm |= IXGBE_FDIRM_VLANID;
1743 case 0x0FFF:
1744 /* mask VLAN priority */
1745 fdirm |= IXGBE_FDIRM_VLANP;
1746 break;
1747 case 0xE000:
1748 /* mask VLAN ID only, fall through */
1749 fdirm |= IXGBE_FDIRM_VLANID;
1750 case 0xEFFF:
1751 /* no VLAN fields masked */
1752 break;
1753 default:
1754 DEBUGOUT(" Error on VLAN mask\n");
1755 return IXGBE_ERR_CONFIG;
1756 }
1757
1758 switch (input_mask->formatted.flex_bytes & 0xFFFF) {
1759 case 0x0000:
1760 /* Mask Flex Bytes, fall through */
1761 fdirm |= IXGBE_FDIRM_FLEX;
1762 case 0xFFFF:
1763 break;
1764 default:
1765 DEBUGOUT(" Error on flexible byte mask\n");
1766 return IXGBE_ERR_CONFIG;
1767 }
1768
1769 if (cloud_mode) {
1770 fdirm |= IXGBE_FDIRM_L3P;
1771 fdirip6m = ((u32) 0xFFFFU << IXGBE_FDIRIP6M_DIPM_SHIFT);
1772 fdirip6m |= IXGBE_FDIRIP6M_ALWAYS_MASK;
1773
1774 switch (input_mask->formatted.inner_mac[0] & 0xFF) {
1775 case 0x00:
1776 /* Mask inner MAC, fall through */
1777 fdirip6m |= IXGBE_FDIRIP6M_INNER_MAC;
1778 case 0xFF:
1779 break;
1780 default:
1781 DEBUGOUT(" Error on inner_mac byte mask\n");
1782 return IXGBE_ERR_CONFIG;
1783 }
1784
1785 switch (input_mask->formatted.tni_vni & 0xFFFFFFFF) {
1786 case 0x0:
1787 /* Mask vxlan id */
1788 fdirip6m |= IXGBE_FDIRIP6M_TNI_VNI;
1789 break;
1790 case 0x00FFFFFF:
1791 fdirip6m |= IXGBE_FDIRIP6M_TNI_VNI_24;
1792 break;
1793 case 0xFFFFFFFF:
1794 break;
1795 default:
1796 DEBUGOUT(" Error on TNI/VNI byte mask\n");
1797 return IXGBE_ERR_CONFIG;
1798 }
1799
1800 switch (input_mask->formatted.tunnel_type & 0xFFFF) {
1801 case 0x0:
1802 /* Mask turnnel type, fall through */
1803 fdirip6m |= IXGBE_FDIRIP6M_TUNNEL_TYPE;
1804 case 0xFFFF:
1805 break;
1806 default:
1807 DEBUGOUT(" Error on tunnel type byte mask\n");
1808 return IXGBE_ERR_CONFIG;
1809 }
1810 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIP6M, fdirip6m);
1811
1812 /* Set all bits in FDIRTCPM, FDIRUDPM, FDIRSIP4M and
1813 * FDIRDIP4M in cloud mode to allow L3/L3 packets to
1814 * tunnel.
1815 */
1816 IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, 0xFFFFFFFF);
1817 IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, 0xFFFFFFFF);
1818 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M, 0xFFFFFFFF);
1819 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M, 0xFFFFFFFF);
1820 }
1821
1822 /* Now mask VM pool and destination IPv6 - bits 5 and 2 */
1823 IXGBE_WRITE_REG(hw, IXGBE_FDIRM, fdirm);
1824
1825 if (!cloud_mode) {
1826 /* store the TCP/UDP port masks, bit reversed from port
1827 * layout */
1828 fdirtcpm = ixgbe_get_fdirtcpm_82599(input_mask);
1829
1830 /* write both the same so that UDP and TCP use the same mask */
1831 IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, ~fdirtcpm);
1832 IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, ~fdirtcpm);
1833 /* also use it for SCTP */
1834 switch (hw->mac.type) {
1835 case ixgbe_mac_X550:
1836 case ixgbe_mac_X550EM_x:
1837 IXGBE_WRITE_REG(hw, IXGBE_FDIRSCTPM, ~fdirtcpm);
1838 break;
1839 default:
1840 break;
1841 }
1842
1843 /* store source and destination IP masks (big-enian) */
1844 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M,
1845 ~input_mask->formatted.src_ip[0]);
1846 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M,
1847 ~input_mask->formatted.dst_ip[0]);
1848 }
1849 return IXGBE_SUCCESS;
1850 }
1851
1852 s32 ixgbe_fdir_write_perfect_filter_82599(struct ixgbe_hw *hw,
1853 union ixgbe_atr_input *input,
1854 u16 soft_id, u8 queue, bool cloud_mode)
1855 {
1856 u32 fdirport, fdirvlan, fdirhash, fdircmd;
1857 u32 addr_low, addr_high;
1858 u32 cloud_type = 0;
1859 s32 err;
1860
1861 DEBUGFUNC("ixgbe_fdir_write_perfect_filter_82599");
1862 if (!cloud_mode) {
1863 /* currently IPv6 is not supported, must be programmed with 0 */
1864 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(0),
1865 input->formatted.src_ip[0]);
1866 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(1),
1867 input->formatted.src_ip[1]);
1868 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(2),
1869 input->formatted.src_ip[2]);
1870
1871 /* record the source address (big-endian) */
1872 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPSA,
1873 input->formatted.src_ip[0]);
1874
1875 /* record the first 32 bits of the destination address
1876 * (big-endian) */
1877 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPDA,
1878 input->formatted.dst_ip[0]);
1879
1880 /* record source and destination port (little-endian)*/
1881 fdirport = IXGBE_NTOHS(input->formatted.dst_port);
1882 fdirport <<= IXGBE_FDIRPORT_DESTINATION_SHIFT;
1883 fdirport |= IXGBE_NTOHS(input->formatted.src_port);
1884 IXGBE_WRITE_REG(hw, IXGBE_FDIRPORT, fdirport);
1885 }
1886
1887 /* record VLAN (little-endian) and flex_bytes(big-endian) */
1888 fdirvlan = IXGBE_STORE_AS_BE16(input->formatted.flex_bytes);
1889 fdirvlan <<= IXGBE_FDIRVLAN_FLEX_SHIFT;
1890 fdirvlan |= IXGBE_NTOHS(input->formatted.vlan_id);
1891 IXGBE_WRITE_REG(hw, IXGBE_FDIRVLAN, fdirvlan);
1892
1893 if (cloud_mode) {
1894 if (input->formatted.tunnel_type != 0)
1895 cloud_type = 0x80000000;
1896
1897 addr_low = ((u32)input->formatted.inner_mac[0] |
1898 ((u32)input->formatted.inner_mac[1] << 8) |
1899 ((u32)input->formatted.inner_mac[2] << 16) |
1900 ((u32)input->formatted.inner_mac[3] << 24));
1901 addr_high = ((u32)input->formatted.inner_mac[4] |
1902 ((u32)input->formatted.inner_mac[5] << 8));
1903 cloud_type |= addr_high;
1904 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(0), addr_low);
1905 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(1), cloud_type);
1906 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(2), input->formatted.tni_vni);
1907 }
1908
1909 /* configure FDIRHASH register */
1910 fdirhash = input->formatted.bkt_hash;
1911 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT;
1912 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1913
1914 /*
1915 * flush all previous writes to make certain registers are
1916 * programmed prior to issuing the command
1917 */
1918 IXGBE_WRITE_FLUSH(hw);
1919
1920 /* configure FDIRCMD register */
1921 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE |
1922 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN;
1923 if (queue == IXGBE_FDIR_DROP_QUEUE)
1924 fdircmd |= IXGBE_FDIRCMD_DROP;
1925 if (input->formatted.flow_type & IXGBE_ATR_L4TYPE_TUNNEL_MASK)
1926 fdircmd |= IXGBE_FDIRCMD_TUNNEL_FILTER;
1927 fdircmd |= input->formatted.flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT;
1928 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT;
1929 fdircmd |= (u32)input->formatted.vm_pool << IXGBE_FDIRCMD_VT_POOL_SHIFT;
1930
1931 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, fdircmd);
1932 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd);
1933 if (err) {
1934 DEBUGOUT("Flow Director command did not complete!\n");
1935 return err;
1936 }
1937
1938 return IXGBE_SUCCESS;
1939 }
1940
1941 s32 ixgbe_fdir_erase_perfect_filter_82599(struct ixgbe_hw *hw,
1942 union ixgbe_atr_input *input,
1943 u16 soft_id)
1944 {
1945 u32 fdirhash;
1946 u32 fdircmd;
1947 s32 err;
1948
1949 /* configure FDIRHASH register */
1950 fdirhash = input->formatted.bkt_hash;
1951 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT;
1952 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1953
1954 /* flush hash to HW */
1955 IXGBE_WRITE_FLUSH(hw);
1956
1957 /* Query if filter is present */
1958 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, IXGBE_FDIRCMD_CMD_QUERY_REM_FILT);
1959
1960 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd);
1961 if (err) {
1962 DEBUGOUT("Flow Director command did not complete!\n");
1963 return err;
1964 }
1965
1966 /* if filter exists in hardware then remove it */
1967 if (fdircmd & IXGBE_FDIRCMD_FILTER_VALID) {
1968 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
1969 IXGBE_WRITE_FLUSH(hw);
1970 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
1971 IXGBE_FDIRCMD_CMD_REMOVE_FLOW);
1972 }
1973
1974 return IXGBE_SUCCESS;
1975 }
1976
1977 /**
1978 * ixgbe_fdir_add_perfect_filter_82599 - Adds a perfect filter
1979 * @hw: pointer to hardware structure
1980 * @input: input bitstream
1981 * @input_mask: mask for the input bitstream
1982 * @soft_id: software index for the filters
1983 * @queue: queue index to direct traffic to
1984 *
1985 * Note that the caller to this function must lock before calling, since the
1986 * hardware writes must be protected from one another.
1987 **/
1988 s32 ixgbe_fdir_add_perfect_filter_82599(struct ixgbe_hw *hw,
1989 union ixgbe_atr_input *input,
1990 union ixgbe_atr_input *input_mask,
1991 u16 soft_id, u8 queue, bool cloud_mode)
1992 {
1993 s32 err = IXGBE_ERR_CONFIG;
1994
1995 DEBUGFUNC("ixgbe_fdir_add_perfect_filter_82599");
1996
1997 /*
1998 * Check flow_type formatting, and bail out before we touch the hardware
1999 * if there's a configuration issue
2000 */
2001 switch (input->formatted.flow_type) {
2002 case IXGBE_ATR_FLOW_TYPE_IPV4:
2003 case IXGBE_ATR_FLOW_TYPE_TUNNELED_IPV4:
2004 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK;
2005 if (input->formatted.dst_port || input->formatted.src_port) {
2006 DEBUGOUT(" Error on src/dst port\n");
2007 return IXGBE_ERR_CONFIG;
2008 }
2009 break;
2010 case IXGBE_ATR_FLOW_TYPE_SCTPV4:
2011 case IXGBE_ATR_FLOW_TYPE_TUNNELED_SCTPV4:
2012 if (input->formatted.dst_port || input->formatted.src_port) {
2013 DEBUGOUT(" Error on src/dst port\n");
2014 return IXGBE_ERR_CONFIG;
2015 }
2016 case IXGBE_ATR_FLOW_TYPE_TCPV4:
2017 case IXGBE_ATR_FLOW_TYPE_TUNNELED_TCPV4:
2018 case IXGBE_ATR_FLOW_TYPE_UDPV4:
2019 case IXGBE_ATR_FLOW_TYPE_TUNNELED_UDPV4:
2020 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK |
2021 IXGBE_ATR_L4TYPE_MASK;
2022 break;
2023 default:
2024 DEBUGOUT(" Error on flow type input\n");
2025 return err;
2026 }
2027
2028 /* program input mask into the HW */
2029 err = ixgbe_fdir_set_input_mask_82599(hw, input_mask, cloud_mode);
2030 if (err)
2031 return err;
2032
2033 /* apply mask and compute/store hash */
2034 ixgbe_atr_compute_perfect_hash_82599(input, input_mask);
2035
2036 /* program filters to filter memory */
2037 return ixgbe_fdir_write_perfect_filter_82599(hw, input,
2038 soft_id, queue, cloud_mode);
2039 }
2040
2041 /**
2042 * ixgbe_read_analog_reg8_82599 - Reads 8 bit Omer analog register
2043 * @hw: pointer to hardware structure
2044 * @reg: analog register to read
2045 * @val: read value
2046 *
2047 * Performs read operation to Omer analog register specified.
2048 **/
2049 s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val)
2050 {
2051 u32 core_ctl;
2052
2053 DEBUGFUNC("ixgbe_read_analog_reg8_82599");
2054
2055 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, IXGBE_CORECTL_WRITE_CMD |
2056 (reg << 8));
2057 IXGBE_WRITE_FLUSH(hw);
2058 usec_delay(10);
2108
2109 /* We need to run link autotry after the driver loads */
2110 hw->mac.autotry_restart = TRUE;
2111
2112 if (ret_val == IXGBE_SUCCESS)
2113 ret_val = ixgbe_verify_fw_version_82599(hw);
2114 out:
2115 return ret_val;
2116 }
2117
2118 /**
2119 * ixgbe_identify_phy_82599 - Get physical layer module
2120 * @hw: pointer to hardware structure
2121 *
2122 * Determines the physical layer module found on the current adapter.
2123 * If PHY already detected, maintains current PHY type in hw struct,
2124 * otherwise executes the PHY detection routine.
2125 **/
2126 s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw)
2127 {
2128 s32 status;
2129
2130 DEBUGFUNC("ixgbe_identify_phy_82599");
2131
2132 /* Detect PHY if not unknown - returns success if already detected. */
2133 status = ixgbe_identify_phy_generic(hw);
2134 if (status != IXGBE_SUCCESS) {
2135 /* 82599 10GBASE-T requires an external PHY */
2136 if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper)
2137 return status;
2138 else
2139 status = ixgbe_identify_module_generic(hw);
2140 }
2141
2142 /* Set PHY type none if no PHY detected */
2143 if (hw->phy.type == ixgbe_phy_unknown) {
2144 hw->phy.type = ixgbe_phy_none;
2145 return IXGBE_SUCCESS;
2146 }
2147
2148 /* Return error if SFP module has been detected but is not supported */
2149 if (hw->phy.type == ixgbe_phy_sfp_unsupported)
2150 return IXGBE_ERR_SFP_NOT_SUPPORTED;
2151
2152 return status;
2153 }
2154
2155 /**
2156 * ixgbe_get_supported_physical_layer_82599 - Returns physical layer type
2157 * @hw: pointer to hardware structure
2158 *
2159 * Determines physical layer capabilities of the current configuration.
2160 **/
2161 u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw)
2162 {
2163 u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
2164 u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2165 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
2166 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
2167 u32 pma_pmd_10g_parallel = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK;
2168 u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
2169 u16 ext_ability = 0;
2170
2171 DEBUGFUNC("ixgbe_get_support_physical_layer_82599");
2172
2173 hw->phy.ops.identify(hw);
2174
2175 switch (hw->phy.type) {
2176 case ixgbe_phy_tn:
2177 case ixgbe_phy_cu_unknown:
2178 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY,
2179 IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability);
2180 if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY)
2181 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
2182 if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
2183 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
2184 if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY)
2185 physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
2186 goto out;
2187 default:
2188 break;
2189 }
2190
2191 switch (autoc & IXGBE_AUTOC_LMS_MASK) {
2192 case IXGBE_AUTOC_LMS_1G_AN:
2193 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
2194 if (pma_pmd_1g == IXGBE_AUTOC_1G_KX_BX) {
2195 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX |
2196 IXGBE_PHYSICAL_LAYER_1000BASE_BX;
2197 goto out;
2198 } else
2199 /* SFI mode so read SFP module */
2200 goto sfp_check;
2201 break;
2202 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
2203 if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_CX4)
2204 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
2205 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_KX4)
2206 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
2207 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_XAUI)
2208 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_XAUI;
2209 goto out;
2210 break;
2211 case IXGBE_AUTOC_LMS_10G_SERIAL:
2212 if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_KR) {
2213 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR;
2214 goto out;
2215 } else if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)
2216 goto sfp_check;
2217 break;
2218 case IXGBE_AUTOC_LMS_KX4_KX_KR:
2219 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
2220 if (autoc & IXGBE_AUTOC_KX_SUPP)
2221 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX;
2222 if (autoc & IXGBE_AUTOC_KX4_SUPP)
2223 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
2224 if (autoc & IXGBE_AUTOC_KR_SUPP)
2225 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KR;
2226 goto out;
2227 break;
2228 default:
2229 goto out;
2230 break;
2231 }
2232
2233 sfp_check:
2234 /* SFP check must be done last since DA modules are sometimes used to
2235 * test KR mode - we need to id KR mode correctly before SFP module.
2236 * Call identify_sfp because the pluggable module may have changed */
2237 physical_layer = ixgbe_get_supported_phy_sfp_layer_generic(hw);
2238 out:
2239 return physical_layer;
2240 }
2241
2242 /**
2243 * ixgbe_enable_rx_dma_82599 - Enable the Rx DMA unit on 82599
2244 * @hw: pointer to hardware structure
2245 * @regval: register value to write to RXCTRL
2246 *
2247 * Enables the Rx DMA unit for 82599
2248 **/
2249 s32 ixgbe_enable_rx_dma_82599(struct ixgbe_hw *hw, u32 regval)
2250 {
2251
2252 DEBUGFUNC("ixgbe_enable_rx_dma_82599");
2253
2254 /*
2255 * Workaround for 82599 silicon errata when enabling the Rx datapath.
2256 * If traffic is incoming before we enable the Rx unit, it could hang
2257 * the Rx DMA unit. Therefore, make sure the security engine is
2258 * completely disabled prior to enabling the Rx unit.
2259 */
2260
2261 hw->mac.ops.disable_sec_rx_path(hw);
2262
2263 if (regval & IXGBE_RXCTRL_RXEN)
2264 ixgbe_enable_rx(hw);
2265 else
2266 ixgbe_disable_rx(hw);
2267
2268 hw->mac.ops.enable_sec_rx_path(hw);
2269
2270 return IXGBE_SUCCESS;
2271 }
2272
2273 /**
2274 * ixgbe_verify_fw_version_82599 - verify FW version for 82599
2275 * @hw: pointer to hardware structure
2276 *
2277 * Verifies that installed the firmware version is 0.6 or higher
2278 * for SFI devices. All 82599 SFI devices should have version 0.6 or higher.
2279 *
2280 * Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or
2281 * if the FW version is not supported.
2282 **/
2283 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw)
2284 {
2285 s32 status = IXGBE_ERR_EEPROM_VERSION;
2286 u16 fw_offset, fw_ptp_cfg_offset;
2287 u16 fw_version;
2288
2289 DEBUGFUNC("ixgbe_verify_fw_version_82599");
2290
2291 /* firmware check is only necessary for SFI devices */
2292 if (hw->phy.media_type != ixgbe_media_type_fiber) {
2293 status = IXGBE_SUCCESS;
2294 goto fw_version_out;
2295 }
2296
2297 /* get the offset to the Firmware Module block */
2298 if (hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset)) {
2299 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE,
2300 "eeprom read at offset %d failed", IXGBE_FW_PTR);
2301 return IXGBE_ERR_EEPROM_VERSION;
2302 }
2303
2304 if ((fw_offset == 0) || (fw_offset == 0xFFFF))
2305 goto fw_version_out;
2306
2307 /* get the offset to the Pass Through Patch Configuration block */
2308 if (hw->eeprom.ops.read(hw, (fw_offset +
2309 IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR),
2310 &fw_ptp_cfg_offset)) {
2311 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE,
2312 "eeprom read at offset %d failed",
2313 fw_offset +
2314 IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR);
2315 return IXGBE_ERR_EEPROM_VERSION;
2316 }
2317
2318 if ((fw_ptp_cfg_offset == 0) || (fw_ptp_cfg_offset == 0xFFFF))
2319 goto fw_version_out;
2320
2321 /* get the firmware version */
2322 if (hw->eeprom.ops.read(hw, (fw_ptp_cfg_offset +
2323 IXGBE_FW_PATCH_VERSION_4), &fw_version)) {
2324 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE,
2325 "eeprom read at offset %d failed",
2326 fw_ptp_cfg_offset + IXGBE_FW_PATCH_VERSION_4);
2327 return IXGBE_ERR_EEPROM_VERSION;
2328 }
2329
2330 if (fw_version > 0x5)
2331 status = IXGBE_SUCCESS;
2332
2333 fw_version_out:
2334 return status;
2335 }
2336
2337 /**
2338 * ixgbe_verify_lesm_fw_enabled_82599 - Checks LESM FW module state.
2339 * @hw: pointer to hardware structure
2340 *
2341 * Returns TRUE if the LESM FW module is present and enabled. Otherwise
2342 * returns FALSE. Smart Speed must be disabled if LESM FW module is enabled.
2343 **/
2344 bool ixgbe_verify_lesm_fw_enabled_82599(struct ixgbe_hw *hw)
2345 {
2346 bool lesm_enabled = FALSE;
2347 u16 fw_offset, fw_lesm_param_offset, fw_lesm_state;
2348 s32 status;
2349
2350 DEBUGFUNC("ixgbe_verify_lesm_fw_enabled_82599");
2351
2352 /* get the offset to the Firmware Module block */
2353 status = hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset);
2354
2355 if ((status != IXGBE_SUCCESS) ||
2356 (fw_offset == 0) || (fw_offset == 0xFFFF))
2357 goto out;
2358
2359 /* get the offset to the LESM Parameters block */
2360 status = hw->eeprom.ops.read(hw, (fw_offset +
2361 IXGBE_FW_LESM_PARAMETERS_PTR),
2362 &fw_lesm_param_offset);
2363
2364 if ((status != IXGBE_SUCCESS) ||
2365 (fw_lesm_param_offset == 0) || (fw_lesm_param_offset == 0xFFFF))
2366 goto out;
2367
2368 /* get the LESM state word */
2369 status = hw->eeprom.ops.read(hw, (fw_lesm_param_offset +
2370 IXGBE_FW_LESM_STATE_1),
2371 &fw_lesm_state);
2372
2373 if ((status == IXGBE_SUCCESS) &&
2374 (fw_lesm_state & IXGBE_FW_LESM_STATE_ENABLED))
2375 lesm_enabled = TRUE;
2376
2377 out:
2378 return lesm_enabled;
2379 }
2380
2381 /**
2382 * ixgbe_read_eeprom_buffer_82599 - Read EEPROM word(s) using
2383 * fastest available method
2384 *
2385 * @hw: pointer to hardware structure
2386 * @offset: offset of word in EEPROM to read
2387 * @words: number of words
2388 * @data: word(s) read from the EEPROM
2427 u16 offset, u16 *data)
2428 {
2429 struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
2430 s32 ret_val = IXGBE_ERR_CONFIG;
2431
2432 DEBUGFUNC("ixgbe_read_eeprom_82599");
2433
2434 /*
2435 * If EEPROM is detected and can be addressed using 14 bits,
2436 * use EERD otherwise use bit bang
2437 */
2438 if ((eeprom->type == ixgbe_eeprom_spi) &&
2439 (offset <= IXGBE_EERD_MAX_ADDR))
2440 ret_val = ixgbe_read_eerd_generic(hw, offset, data);
2441 else
2442 ret_val = ixgbe_read_eeprom_bit_bang_generic(hw, offset, data);
2443
2444 return ret_val;
2445 }
2446
2447 /**
2448 * ixgbe_reset_pipeline_82599 - perform pipeline reset
2449 *
2450 * @hw: pointer to hardware structure
2451 *
2452 * Reset pipeline by asserting Restart_AN together with LMS change to ensure
2453 * full pipeline reset. This function assumes the SW/FW lock is held.
2454 **/
2455 s32 ixgbe_reset_pipeline_82599(struct ixgbe_hw *hw)
2456 {
2457 s32 ret_val;
2458 u32 anlp1_reg = 0;
2459 u32 i, autoc_reg, autoc2_reg;
2460
2461 /* Enable link if disabled in NVM */
2462 autoc2_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
2463 if (autoc2_reg & IXGBE_AUTOC2_LINK_DISABLE_MASK) {
2464 autoc2_reg &= ~IXGBE_AUTOC2_LINK_DISABLE_MASK;
2465 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2_reg);
2466 IXGBE_WRITE_FLUSH(hw);
2467 }
2468
2469 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2470 autoc_reg |= IXGBE_AUTOC_AN_RESTART;
2471 /* Write AUTOC register with toggled LMS[2] bit and Restart_AN */
2472 IXGBE_WRITE_REG(hw, IXGBE_AUTOC,
2473 autoc_reg ^ (0x4 << IXGBE_AUTOC_LMS_SHIFT));
2474 /* Wait for AN to leave state 0 */
2475 for (i = 0; i < 10; i++) {
2476 msec_delay(4);
2477 anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
2478 if (anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)
2479 break;
2480 }
2481
2482 if (!(anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)) {
2483 DEBUGOUT("auto negotiation not completed\n");
2484 ret_val = IXGBE_ERR_RESET_FAILED;
2485 goto reset_pipeline_out;
2486 }
2487
2488 ret_val = IXGBE_SUCCESS;
2489
2490 reset_pipeline_out:
2491 /* Write AUTOC register with original LMS field and Restart_AN */
2492 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
2493 IXGBE_WRITE_FLUSH(hw);
2494
2495 return ret_val;
2496 }
2497
2498 /**
2499 * ixgbe_read_i2c_byte_82599 - Reads 8 bit word over I2C
2500 * @hw: pointer to hardware structure
2501 * @byte_offset: byte offset to read
2502 * @data: value read
2503 *
2504 * Performs byte read operation to SFP module's EEPROM over I2C interface at
2505 * a specified device address.
2506 **/
2507 static s32 ixgbe_read_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset,
2508 u8 dev_addr, u8 *data)
2509 {
2510 u32 esdp;
2511 s32 status;
2512 s32 timeout = 200;
2513
2514 DEBUGFUNC("ixgbe_read_i2c_byte_82599");
2515
2516 if (hw->phy.qsfp_shared_i2c_bus == TRUE) {
2517 /* Acquire I2C bus ownership. */
2518 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2519 esdp |= IXGBE_ESDP_SDP0;
2520 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
2521 IXGBE_WRITE_FLUSH(hw);
2522
2523 while (timeout) {
2524 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2525 if (esdp & IXGBE_ESDP_SDP1)
2526 break;
2527
2528 msec_delay(5);
2529 timeout--;
2530 }
2531
2532 if (!timeout) {
2533 DEBUGOUT("Driver can't access resource,"
2534 " acquiring I2C bus timeout.\n");
2535 status = IXGBE_ERR_I2C;
2536 goto release_i2c_access;
2537 }
2538 }
2539
2540 status = ixgbe_read_i2c_byte_generic(hw, byte_offset, dev_addr, data);
2541
2542 release_i2c_access:
2543
2544 if (hw->phy.qsfp_shared_i2c_bus == TRUE) {
2545 /* Release I2C bus ownership. */
2546 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2547 esdp &= ~IXGBE_ESDP_SDP0;
2548 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
2549 IXGBE_WRITE_FLUSH(hw);
2550 }
2551
2552 return status;
2553 }
2554
2555 /**
2556 * ixgbe_write_i2c_byte_82599 - Writes 8 bit word over I2C
2557 * @hw: pointer to hardware structure
2558 * @byte_offset: byte offset to write
2559 * @data: value to write
2560 *
2561 * Performs byte write operation to SFP module's EEPROM over I2C interface at
2562 * a specified device address.
2563 **/
2564 static s32 ixgbe_write_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset,
2565 u8 dev_addr, u8 data)
2566 {
2567 u32 esdp;
2568 s32 status;
2569 s32 timeout = 200;
2570
2571 DEBUGFUNC("ixgbe_write_i2c_byte_82599");
2572
2573 if (hw->phy.qsfp_shared_i2c_bus == TRUE) {
2574 /* Acquire I2C bus ownership. */
2575 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2576 esdp |= IXGBE_ESDP_SDP0;
2577 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
2578 IXGBE_WRITE_FLUSH(hw);
2579
2580 while (timeout) {
2581 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2582 if (esdp & IXGBE_ESDP_SDP1)
2583 break;
2584
2585 msec_delay(5);
2586 timeout--;
2587 }
2588
2589 if (!timeout) {
2590 DEBUGOUT("Driver can't access resource,"
2591 " acquiring I2C bus timeout.\n");
2592 status = IXGBE_ERR_I2C;
2593 goto release_i2c_access;
2594 }
2595 }
2596
2597 status = ixgbe_write_i2c_byte_generic(hw, byte_offset, dev_addr, data);
2598
2599 release_i2c_access:
2600
2601 if (hw->phy.qsfp_shared_i2c_bus == TRUE) {
2602 /* Release I2C bus ownership. */
2603 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
2604 esdp &= ~IXGBE_ESDP_SDP0;
2605 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
2606 IXGBE_WRITE_FLUSH(hw);
2607 }
2608
2609 return status;
2610 }
|