1 /*
2 * This file and its contents are supplied under the terms of the
3 * Common Development and Distribution License ("CDDL"), version 1.0.
4 * You may only use this file in accordance with the terms of version
5 * 1.0 of the CDDL.
6 *
7 * A full copy of the text of the CDDL should have accompanied this
8 * source. A copy of the CDDL is also available via the Internet at
9 * http://www.illumos.org/license/CDDL.
10 */
11
12 /*
13 * Copyright (c) 2017, Joyent, Inc.
14 */
15
16 /*
17 * Extensible Host Controller Interface (xHCI) USB Driver
18 *
19 * The xhci driver is an HCI driver for USB that bridges the gap between client
20 * device drivers and implements the actual way that we talk to devices. The
21 * xhci specification provides access to USB 3.x capable devices, as well as all
22 * prior generations. Like other host controllers, it both provides the way to
23 * talk to devices and also is treated like a hub (often called the root hub).
24 *
25 * This driver is part of the USBA (USB Architecture). It implements the HCDI
26 * (host controller device interface) end of USBA. These entry points are used
27 * by the USBA on behalf of client device drivers to access their devices. The
28 * driver also provides notifications to deal with hot plug events, which are
29 * quite common in USB.
30 *
31 * ----------------
32 * USB Introduction
33 * ----------------
34 *
35 * To properly understand the xhci driver and the design of the USBA HCDI
36 * interfaces it implements, it helps to have a bit of background into how USB
37 * devices are structured and understand how they work at a high-level.
38 *
39 * USB devices, like PCI devices, are broken down into different classes of
40 * device. For example, with USB you have hubs, human-input devices (keyboards,
41 * mice, etc.), mass storage, etc. Every device also has a vendor and device ID.
42 * Many client drivers bind to an entire class of device, for example, the hubd
43 * driver (to hubs) or scsa2usb (USB storage). However, there are other drivers
44 * that bind to explicit IDs such as usbsprl (specific USB to Serial devices).
45 *
46 * USB SPEEDS AND VERSIONS
47 *
48 * USB devices are often referred to in two different ways. One way they're
49 * described is with the USB version that they conform to. In the wild, you're
50 * most likely going to see USB 1.1, 2.0, 2.1, and 3.0. However, you may also
51 * see devices referred to as 'full-', 'low-', 'high-', and 'super-' speed
52 * devices.
53 *
54 * The latter description describes the maximum theoretical speed of a given
55 * device. For example, a super-speed device theoretically caps out around 5
56 * Gbit/s, whereas a low-speed device caps out at 1.5 Mbit/s.
57 *
58 * In general, each speed usually corresponds to a specific USB protocol
59 * generation. For example, all USB 3.0 devices are super-speed devices. All
60 * 'high-speed' devices are USB 2.x devices. Full-speed devices are special in
61 * that they can either be USB 1.x or USB 2.x devices. Low-speed devices are
62 * only a USB 1.x thing, they did not jump the fire line to USB 2.x.
63 *
64 * USB 3.0 devices and ports generally have the wiring for both USB 2.0 and USB
65 * 3.0. When a USB 3.x device is plugged into a USB 2.0 port or hub, then it
66 * will report its version as USB 2.1, to indicate that it is actually a USB 3.x
67 * device.
68 *
69 * USB ENDPOINTS
70 *
71 * A given USB device is made up of endpoints. A request, or transfer, is made
72 * to a specific USB endpoint. These endpoints can provide different services
73 * and have different expectations around the size of the data that'll be used
74 * in a given request and the periodicity of requests. Endpoints themselves are
75 * either used to make one-shot requests, for example, making requests to a mass
76 * storage device for a given sector, or for making periodic requests where you
77 * end up polling on the endpoint, for example, polling on a USB keyboard for
78 * keystrokes.
79 *
80 * Each endpoint encodes two different pieces of information: a direction and a
81 * type. There are two different directions: IN and OUT. These refer to the
82 * general direction that data moves relative to the operating system. For
83 * example, an IN transfer transfers data in to the operating system, from the
84 * device. An OUT transfer transfers data from the operating system, out to the
85 * device.
86 *
87 * There are four different kinds of endpoints:
88 *
89 * BULK These transfers are large transfers of data to or from
90 * a device. The most common use for bulk transfers is for
91 * mass storage devices. Though they are often also used by
92 * network devices and more. Bulk endpoints do not have an
93 * explicit time component to them. They are always used
94 * for one-shot transfers.
95 *
96 * CONTROL These transfers are used to manipulate devices
97 * themselves and are used for USB protocol level
98 * operations (whether device-specific, class-specific, or
99 * generic across all of USB). Unlike other transfers,
100 * control transfers are always bi-directional and use
101 * different kinds of transfers.
102 *
103 * INTERRUPT Interrupt transfers are used for small transfers that
104 * happen infrequently, but need reasonable latency. A good
105 * example of interrupt transfers is to receive input from
106 * a USB keyboard. Interrupt-IN transfers are generally
107 * polled. Meaning that a client (device driver) opens up
108 * an interrupt-IN pipe to poll on it, and receives
109 * periodic updates whenever there is information
110 * available. However, Interrupt transfers can be used
111 * as one-shot transfers both going IN and OUT.
112 *
113 * ISOCHRONOUS These transfers are things that happen once per
114 * time-interval at a very regular rate. A good example of
115 * these transfers are for audio and video. A device may
116 * describe an interval as 10ms at which point it will read
117 * or write the next batch of data every 10ms and transform
118 * it for the user. There are no one-shot Isochronous-IN
119 * transfers. There are one-shot Isochronous-OUT transfers,
120 * but these are used by device drivers to always provide
121 * the system with sufficient data.
122 *
123 * To find out information about the endpoints, USB devices have a series of
124 * descriptors that cover different aspects of the device. For example, there
125 * are endpoint descriptors which cover the properties of endpoints such as the
126 * maximum packet size or polling interval.
127 *
128 * Descriptors exist at all levels of USB. For example, there are general
129 * descriptors for every device. The USB device descriptor is described in
130 * usb_dev_descr(9S). Host controllers will look at these descriptors to ensure
131 * that they program the device correctly; however, they are more often used by
132 * client device drivers. There are also descriptors that exist at a class
133 * level. For example, the hub class has a class-specific descriptor which
134 * describes properties of the hub. That information is requested for and used
135 * by the hub driver.
136 *
137 * All of the different descriptors are gathered by the system and placed into a
138 * tree which USBA sometimes calls the 'Configuration Cloud'. Client device
139 * drivers gain access to this cloud and then use them to open endpoints, which
140 * are called pipes in USBA (and some revisions of the USB specification).
141 *
142 * Each pipe gives access to a specific endpoint on the device which can be used
143 * to perform transfers of a specific type and direction. For example, a mass
144 * storage device often has three different endpoints, the default control
145 * endpoint (which every device has), a Bulk-IN endpoint, and a Bulk-OUT
146 * endpoint. The device driver ends up with three open pipes. One to the default
147 * control endpoint to configure the device, and then the other two are used to
148 * perform I/O.
149 *
150 * These routines translate more or less directly into calls to a host
151 * controller driver. A request to open a pipe takes an endpoint descriptor that
152 * describes the properties of the pipe, and the host controller driver (this
153 * driver) goes through and does any work necessary to allow the client device
154 * driver to access it. Once the pipe is open, it either makes one-shot
155 * transfers specific to the transfer type or it starts performing a periodic
156 * poll of an endpoint.
157 *
158 * All of these different actions translate into requests to the host
159 * controller. The host controller driver itself is in charge of making sure
160 * that all of the required resources for polling are allocated with a request
161 * and then proceed to give the driver's periodic callbacks.
162 *
163 * HUBS AND HOST CONTROLLERS
164 *
165 * Every device is always plugged into a hub, even if the device is itself a
166 * hub. This continues until we reach what we call the root-hub. The root-hub is
167 * special in that it is not an actual USB hub, but is integrated into the host
168 * controller and is manipulated in its own way. For example, the host
169 * controller is used to turn on and off a given port's power. This may happen
170 * over any interface, though the most common way is through PCI.
171 *
172 * In addition to the normal character device that exists for a host controller
173 * driver, as part of attaching, the host controller binds to an instance of the
174 * hubd driver. While the root-hub is a bit of a fiction, everyone models the
175 * root-hub as the same as any other hub that's plugged in. The hub kernel
176 * module doesn't know that the hub isn't a physical device that's been plugged
177 * in. The host controller driver simulates that view by taking hub requests
178 * that are made and translating them into corresponding requests that are
179 * understood by the host controller, for example, reading and writing to a
180 * memory mapped register.
181 *
182 * The hub driver polls for changes in device state using an Interrupt-IN
183 * request, which is the same as is done for the root-hub. This allows the host
184 * controller driver to not have to know about the implementation of device hot
185 * plug, merely react to requests from a hub, the same as if it were an external
186 * device. When the hub driver detects a change, it will go through the
187 * corresponding state machine and attach or detach the corresponding client
188 * device driver, depending if the device was inserted or removed.
189 *
190 * We detect the changes for the Interrupt-IN primarily based on the port state
191 * change events that are delivered to the event ring. Whenever any event is
192 * fired, we use this to update the hub driver about _all_ ports with
193 * outstanding events. This more closely matches how a hub is supposed to behave
194 * and leaves things less likely for the hub driver to end up without clearing a
195 * flag on a port.
196 *
197 * PACKET SIZES AND BURSTING
198 *
199 * A given USB endpoint has an explicit packet size and a number of packets that
200 * can be sent per time interval. These concepts are abstracted away from client
201 * device drives usually, though they sometimes inform the upper bounds of what
202 * a device can perform.
203 *
204 * The host controller uses this information to transform arbitrary transfer
205 * requests into USB protocol packets. One of the nice things about the host
206 * controllers is that they abstract away all of the signaling and semantics of
207 * the actual USB protocols, allowing for life to be slightly easier in the
208 * operating system.
209 *
210 * That said, if the host controller is not programmed correctly, these can end
211 * up causing transaction errors and other problems in response to the data that
212 * the host controller is trying to send or receive.
213 *
214 * ------------
215 * Organization
216 * ------------
217 *
218 * The driver is made up of the following files. Many of these have their own
219 * theory statements to describe what they do. Here, we touch on each of the
220 * purpose of each of these files.
221 *
222 * xhci_command.c: This file contains the logic to issue commands to the
223 * controller as well as the actual functions that the
224 * other parts of the driver use to cause those commands.
225 *
226 * xhci_context.c: This file manages various data structures used by the
227 * controller to manage the controller's and device's
228 * context data structures. See more in the xHCI Overview
229 * and General Design for more information.
230 *
231 * xhci_dma.c: This manages the allocation of DMA memory and DMA
232 * attributes for controller, whether memory is for a
233 * transfer or something else. This file also deals with
234 * all the logic of getting data in and out of DMA buffers.
235 *
236 * xhci_endpoint.c: This manages all of the logic of handling endpoints or
237 * pipes. It deals with endpoint configuration, I/O
238 * scheduling, timeouts, and callbacks to USBA.
239 *
240 * xhci_event.c: This manages callbacks from the hardware to the driver.
241 * This covers command completion notifications and I/O
242 * notifications.
243 *
244 * xhci_hub.c: This manages the virtual root-hub. It basically
245 * implements and translates all of the USB level requests
246 * into xhci specific implements. It also contains the
247 * functions to register this hub with USBA.
248 *
249 * xhci_intr.c: This manages the underlying interrupt allocation,
250 * interrupt moderation, and interrupt routines.
251 *
252 * xhci_quirks.c: This manages information about buggy hardware that's
253 * been collected and experienced primarily from other
254 * systems.
255 *
256 * xhci_ring.c: This manages the abstraction of a ring in xhci, which is
257 * the primary of communication between the driver and the
258 * hardware, whether for the controller or a device.
259 *
260 * xhci_usba.c: This implements all of the HCDI functions required by
261 * USBA. This is the main entry point that drivers and the
262 * kernel frameworks will reach to start any operation.
263 * Many functions here will end up in the command and
264 * endpoint code.
265 *
266 * xhci.c: This provides the main kernel DDI interfaces and
267 * performs device initialization.
268 *
269 * xhci.h: This is the primary header file which defines
270 * illumos-specific data structures and constants to manage
271 * the system.
272 *
273 * xhcireg.h: This header file defines all of the register offsets,
274 * masks, and related macros. It also contains all of the
275 * constants that are used in various structures as defined
276 * by the specification, such as command offsets, etc.
277 *
278 * xhci_ioctl.h: This contains a few private ioctls that are used by a
279 * private debugging command. These are private.
280 *
281 * cmd/xhci/xhci_portsc: This is a private utility that can be useful for
282 * debugging xhci state. It is the only consumer of
283 * xhci_ioctl.h and the private ioctls.
284 *
285 * ----------------------------------
286 * xHCI Overview and Structure Layout
287 * ----------------------------------
288 *
289 * The design and structure of this driver follows from the way that the xHCI
290 * specification tells us that we have to work with hardware. First we'll give a
291 * rough summary of how that works, though the xHCI 1.1 specification should be
292 * referenced when going through this.
293 *
294 * There are three primary parts of the hardware -- registers, contexts, and
295 * rings. The registers are memory mapped registers that come in four sets,
296 * though all are found within the first BAR. These are used to program and
297 * control the hardware and aspects of the devices. Beyond more traditional
298 * device programming there are two primary sets of registers that are
299 * important:
300 *
301 * o Port Status and Control Registers (XHCI_PORTSC)
302 * o Doorbell Array (XHCI_DOORBELL)
303 *
304 * The port status and control registers are used to get and manipulate the
305 * status of a given device. For example, turning on and off the power to it.
306 * The Doorbell Array is used to kick off I/O operations and start the
307 * processing of an I/O ring.
308 *
309 * The contexts are data structures that represent various pieces of information
310 * in the controller. These contexts are generally filled out by the driver and
311 * then acknowledged and consumed by the hardware. There are controller-wide
312 * contexts (mostly managed in xhci_context.c) that are used to point to the
313 * contexts that exist for each device in the system. The primary context is
314 * called the Device Context Base Address Array (DCBAA).
315 *
316 * Each device in the system is allocated a 'slot', which is used to index into
317 * the DCBAA. Slots are assigned based on issuing commands to the controller.
318 * There are a fixed number of slots that determine the maximum number of
319 * devices that can end up being supported in the system. Note this includes all
320 * the devices plugged into the USB device tree, not just devices plugged into
321 * ports on the chassis.
322 *
323 * For each device, there is a context structure that describes properties of
324 * the device. For example, what speed is the device, is it a hub, etc. The
325 * context has slots for the device and for each endpoint on the device. As
326 * endpoints are enabled, their context information which describes things like
327 * the maximum packet size, is filled in and enabled. The mapping between these
328 * contexts look like:
329 *
330 *
331 * DCBAA
332 * +--------+ Device Context
333 * | Slot 0 |------------------>+--------------+
334 * +--------+ | Slot Context |
335 * | ... | +--------------+ +----------+
336 * +--------+ +------+ | Endpoint 0 |------>| I/O Ring |
337 * | Slot n |-->| NULL | | Context (Bi) | +----------+
338 * +--------+ +------+ +--------------+
339 * | Endpoint 1 |
340 * | Context (Out)|
341 * +--------------+
342 * | Endpoint 1 |
343 * | Context (In) |
344 * +--------------+
345 * | ... |
346 * +--------------+
347 * | Endpoint 15 |
348 * | Context (In) |
349 * +--------------+
350 *
351 * These contexts are always owned by the controller, though we can read them
352 * after various operations complete. Commands that toggle device state use a
353 * specific input context, which is a variant of the device context. The only
354 * difference is that it has an input context structure ahead of it to say which
355 * sections of the device context should be evaluated.
356 *
357 * Each active endpoint points us to an I/O ring, which leads us to the third
358 * main data structure that's used by the device: rings. Rings are made up of
359 * transfer request blocks (TRBs), which are joined together to form a given
360 * transfer description (TD) which represents a single I/O request.
361 *
362 * These rings are used to issue I/O to individual endpoints, to issue commands
363 * to the controller, and to receive notification of changes and completions.
364 * Issued commands go on the special ring called the command ring while the
365 * change and completion notifications go on the event ring. More details are
366 * available in xhci_ring.c. Each of these structures is represented by an
367 * xhci_ring_t.
368 *
369 * Each ring can be made up of one or more disjoint regions of DMA; however, we
370 * only use a single one. This also impacts some additional registers and
371 * structures that exist. The event ring has an indirection table called the
372 * Event Ring Segment Table (ERST). Each entry in the table (a segment)
373 * describes a chunk of the event ring.
374 *
375 * One other thing worth calling out is the scratchpad. The scratchpad is a way
376 * for the controller to be given arbitrary memory by the OS that it can use.
377 * There are two parts to the scratchpad. The first part is an array whose
378 * entries contain pointers to the actual addresses for the pages. The second
379 * part that we allocate are the actual pages themselves.
380 *
381 * -----------------------------
382 * Endpoint State and Management
383 * -----------------------------
384 *
385 * Endpoint management is one of the key parts to the xhci driver as every
386 * endpoint is a pipe that a device driver uses, so they are our primary
387 * currency. Endpoints are enabled and disabled when the client device drivers
388 * open and close a pipe. When an endpoint is enabled, we have to fill in an
389 * endpoint's context structure with information about the endpoint. These
390 * basically tell the controller important properties which it uses to ensure
391 * that there is adequate bandwidth for the device.
392 *
393 * Each endpoint has its own ring as described in the previous section. We place
394 * TRBs (transfer request blocks) onto a given ring to request I/O be performed.
395 * Responses are placed on the event ring, in other words, the rings associated
396 * with an endpoint are purely for producing I/O.
397 *
398 * Endpoints have a defined state machine as described in xHCI 1.1 / 4.8.3.
399 * These states generally correspond with the state of the endpoint to process
400 * I/O and handle timeouts. The driver basically follows a similar state machine
401 * as described there. There are some deviations. For example, what they
402 * describe as 'running' we break into both the Idle and Running states below.
403 * We also have a notion of timed out and quiescing. The following image
404 * summarizes the states and transitions:
405 *
406 * +------+ +-----------+
407 * | Idle |---------*--------------------->| Running |<-+
408 * +------+ . I/O queued on +-----------+ |
409 * ^ ring and timeout | | | |
410 * | scheduled. | | | |
411 * | | | | |
412 * +-----*---------------------------------+ | | |
413 * | . No I/Os remain | | |
414 * | | | |
415 * | +------*------------------+ | |
416 * | | . Timeout | |
417 * | | fires for | |
418 * | | I/O | |
419 * | v v |
420 * | +-----------+ +--------+ |
421 * | | Timed Out | | Halted | |
422 * | +-----------+ +--------+ |
423 * | | | |
424 * | | +-----------+ | |
425 * | +-->| Quiescing |<----------+ |
426 * | +-----------+ |
427 * | No TRBs. | . TRBs |
428 * | remain . | . Remain |
429 * +----------*----<------+-------->-------*-----------+
430 *
431 * Normally, a given endpoint will oscillate between having TRBs scheduled and
432 * not. Every time a new I/O is added to the endpoint, we'll ring the doorbell,
433 * making sure that we're processing the ring, presuming that the endpoint isn't
434 * in one of the error states.
435 *
436 * To detect device hangs, we have an active timeout(9F) per active endpoint
437 * that ticks at a one second rate while we still have TRBs outstanding on an
438 * endpoint. Once all outstanding TRBs have been processed, the timeout will
439 * stop itself and there will be no active checking until the endpoint has I/O
440 * scheduled on it again.
441 *
442 * There are two primary ways that things can go wrong on the endpoint. We can
443 * either have a timeout or an event that transitions the endpoint to the Halted
444 * state. In the halted state, we need to issue explicit commands to reset the
445 * endpoint before removing the I/O.
446 *
447 * The way we handle both a timeout and a halted condition is similar, but the
448 * way they are triggered is different. When we detect a halted condition, we
449 * don't immediately clean it up, and wait for the client device driver (or USBA
450 * on its behalf) to issue a pipe reset. When we detect a timeout, we
451 * immediately take action (assuming no other action is ongoing).
452 *
453 * In both cases, we quiesce the device, which takes care of dealing with taking
454 * the endpoint from whatever state it may be in and taking the appropriate
455 * actions based on the state machine in xHCI 1.1 / 4.8.3. The end of quiescing
456 * leaves the device stopped, which allows us to update the ring's pointer and
457 * remove any TRBs that are causing problems.
458 *
459 * As part of all this, we ensure that we can only be quiescing the device from
460 * a given path at a time. Any requests to schedule I/O during this time will
461 * generally fail.
462 *
463 * The following image describes the state machine for the timeout logic. It
464 * ties into the image above.
465 *
466 * +----------+ +---------+
467 * | Disabled |-----*--------------------->| Enabled |<--+
468 * +----------+ . TRBs scheduled +---------+ *. 1 sec timer
469 * ^ and no active | | | | fires and
470 * | timer. | | | | another
471 * | | | +--+--+ quiesce, in
472 * | | | | a bad state,
473 * +------*------------------------------+ | ^ or decrement
474 * | . 1 sec timer | | I/O timeout
475 * | fires and | |
476 * | no TRBs or | +--------------+
477 * | endpoint shutdown | |
478 * | *. . timer counter |
479 * ^ | reaches zero |
480 * | v |
481 * | +--------------+ |
482 * +-------------*---------------<--| Quiesce ring |->---*-------+
483 * . No more | and fail I/O | . restart
484 * I/Os +--------------+ timer as
485 * more I/Os
486 *
487 * As we described above, when there are active TRBs and I/Os, a 1 second
488 * timeout(9F) will be active. Each second, we decrement a counter on the
489 * current, active I/O until either a new I/O takes the head, or the counter
490 * reaches zero. If the counter reaches zero, then we go through, quiesce the
491 * ring, and then clean things up.
492 *
493 * ------------------
494 * Periodic Endpoints
495 * ------------------
496 *
497 * It's worth calling out periodic endpoints explicitly, as they operate
498 * somewhat differently. Periodic endpoints are limited to Interrupt-IN and
499 * Isochronous-IN. The USBA often uses the term polling for these. That's
500 * because the client only needs to make a single API call; however, they'll
501 * receive multiple callbacks until either an error occurs or polling is
502 * requested to be terminated.
503 *
504 * When we have one of these periodic requests, we end up always rescheduling
505 * I/O requests, as well as, having a specific number of pre-existing I/O
506 * requests to cover the periodic needs, in case of latency spikes. Normally,
507 * when replying to a request, we use the request handle that we were given.
508 * However, when we have a periodic request, we're required to duplicate the
509 * handle before giving them data.
510 *
511 * However, the duplication is a bit tricky. For everything that was duplicated,
512 * the framework expects us to submit data. Because of that we, don't duplicate
513 * them until they are needed. This minimizes the likelihood that we have
514 * outstanding requests to deal with when we encounter a fatal polling failure.
515 *
516 * Most of the polling setup logic happens in xhci_usba.c in
517 * xhci_hcdi_periodic_init(). The consumption and duplication is handled in
518 * xhci_endpoint.c.
519 *
520 * ----------------
521 * Structure Layout
522 * ----------------
523 *
524 * The following images relate the core data structures. The primary structure
525 * in the system is the xhci_t. This is the per-controller data structure that
526 * exists for each instance of the driver. From there, each device in the system
527 * is represented by an xhci_device_t and each endpoint is represented by an
528 * xhci_endpoint_t. For each client that opens a given endpoint, there is an
529 * xhci_pipe_t. For each I/O related ring, there is an xhci_ring_t in the
530 * system.
531 *
532 * +------------------------+
533 * | Per-Controller |
534 * | Structure |
535 * | xhci_t |
536 * | |
537 * | uint_t ---+--> Capability regs offset
538 * | uint_t ---+--> Operational regs offset
539 * | uint_t ---+--> Runtime regs offset
540 * | uint_t ---+--> Doorbell regs offset
541 * | xhci_state_flags_t ---+--> Device state flags
542 * | xhci_quirks_t ---+--> Device quirk flags
543 * | xhci_capability_t ---+--> Controller capability structure
544 * | xhci_dcbaa_t ---+----------------------------------+
545 * | xhci_scratchpad_t ---+---------+ |
546 * | xhci_command_ing_t ---+------+ | v
547 * | xhci_event_ring_t ---+----+ | | +---------------------+
548 * | xhci_usba_t ---+--+ | | | | Device Context |
549 * +------------------------+ | | | | | Base Address |
550 * | | | | | Array Structure |
551 * | | | | | xhci_dcbaa_t |
552 * +-------------------------------+ | | | | |
553 * | +-------------------------------+ | | DCBAA KVA <-+-- uint64_t * |
554 * | | +----------------------------+ | DMA Buffer <-+-- xhci_dma_buffer_t |
555 * | | v | +---------------------+
556 * | | +--------------------------+ +-----------------------+
557 * | | | Event Ring | |
558 * | | | Management | |
559 * | | | xhci_event_ring_t | v
560 * | | | | Event Ring +----------------------+
561 * | | | xhci_event_segment_t * --|-> Segment VA | Scratchpad (Extra |
562 * | | | xhci_dma_buffer_t --|-> Segment DMA Buf. | Controller Memory) |
563 * | | | xhci_ring_t --|--+ | xhci_scratchpad_t |
564 * | | +--------------------------+ | Scratchpad | |
565 * | | | Base Array KVA <-+- uint64_t * |
566 * | +------------+ | Array DMA Buf. <-+- xhci_dma_buffer_t |
567 * | v | Scratchpad DMA <-+- xhci_dma_buffer_t * |
568 * | +---------------------------+ | Buffer per page +----------------------+
569 * | | Command Ring | |
570 * | | xhci_command_ring_t | +------------------------------+
571 * | | | |
572 * | | xhci_ring_t --+-> Command Ring --->------------+
573 * | | list_t --+-> Command List v
574 * | | timeout_id_t --+-> Timeout State +---------------------+
575 * | | xhci_command_ring_state_t +-> State Flags | I/O Ring |
576 * | +---------------------------+ | xhci_ring_t |
577 * | | |
578 * | Ring DMA Buf. <-+-- xhci_dma_buffer_t |
579 * | Ring Length <-+-- uint_t |
580 * | Ring Entry KVA <-+-- xhci_trb_t * |
581 * | +---------------------------+ Ring Head <-+-- uint_t |
582 * +--->| USBA State | Ring Tail <-+-- uint_t |
583 * | xhci_usba_t | Ring Cycle <-+-- uint_t |
584 * | | +---------------------+
585 * | usba_hcdi_ops_t * -+-> USBA Ops Vector ^
586 * | usb_dev_dscr_t -+-> USB Virtual Device Descriptor |
587 * | usb_ss_hub_descr_t -+-> USB Virtual Hub Descriptor |
588 * | usba_pipe_handle_data_t * +-> Interrupt polling client |
589 * | usb_intr_req_t -+-> Interrupt polling request |
590 * | uint32_t --+-> Interrupt polling device mask |
591 * | list_t --+-> Pipe List (Active Users) |
592 * | list_t --+-------------------+ |
593 * +---------------------------+ | ^
594 * | |
595 * v |
596 * +-------------------------------+ +---------------+ |
597 * | USB Device |------------>| USB Device |--> ... |
598 * | xhci_device_t | | xhci_device_t | |
599 * | | +---------------+ |
600 * | usb_port_t --+-> USB Port plugged into |
601 * | uint8_t --+-> Slot Number |
602 * | boolean_t --+-> Address Assigned |
603 * | usba_device_t * --+-> USBA Device State |
604 * | xhci_dma_buffer_t --+-> Input Context DMA Buffer |
605 * | xhci_input_context_t * --+-> Input Context KVA |
606 * | xhci_slot_contex_t * --+-> Input Slot Context KVA |
607 * | xhci_endpoint_context_t *[] --+-> Input Endpoint Context KVA |
608 * | xhci_dma_buffer_t --+-> Output Context DMA Buffer |
609 * | xhci_slot_context_t * --+-> Output Slot Context KVA ^
610 * | xhci_endpoint_context_t *[] --+-> Output Endpoint Context KVA |
611 * | xhci_endpoint_t *[] --+-> Endpoint Tracking ---+ |
612 * +-------------------------------+ | |
613 * | |
614 * v |
615 * +------------------------------+ +-----------------+ |
616 * | Endpoint Data |----------->| Endpoint Data |--> ... |
617 * | xhci_endpoint_t | | xhci_endpoint_t | |
618 * | | +-----------------+ |
619 * | int --+-> Endpoint Number |
620 * | int --+-> Endpoint Type |
621 * | xhci_endpoint_state_t --+-> Endpoint State |
622 * | timeout_id_t --+-> Endpoint Timeout State |
623 * | usba_pipe_handle_data_t * --+-> USBA Client Handle |
624 * | xhci_ring_t --+-> Endpoint I/O Ring -------->--------+
625 * | list_t --+-> Transfer List --------+
626 * +------------------------------+ |
627 * v
628 * +-------------------------+ +--------------------+
629 * | Transfer Structure |----------------->| Transfer Structure |-> ...
630 * | xhci_transfer_t | | xhci_transfer_t |
631 * | | +--------------------+
632 * | xhci_dma_buffer_t --+-> I/O DMA Buffer
633 * | uint_t --+-> Number of TRBs
634 * | uint_t --+-> Short transfer data
635 * | uint_t --+-> Timeout seconds remaining
636 * | usb_cr_t --+-> USB Transfer return value
637 * | boolean_t --+-> Data direction
638 * | xhci_trb_t * --+-> Host-order transfer requests for I/O
639 * | usb_isoc_pkt_descr_t * -+-> Isochronous only response data
640 * | usb_opaque_t --+-> USBA Request Handle
641 * +-------------------------+
642 *
643 * -------------
644 * Lock Ordering
645 * -------------
646 *
647 * There are three different tiers of locks that exist in the driver. First,
648 * there is a lock for each controller: xhci_t`xhci_lock. This protects all the
649 * data for that instance of the controller. If there are multiple instances of
650 * the xHCI controller in the system, each one is independent and protected
651 * separately. The two do not share any data.
652 *
653 * From there, there are two other, specific locks in the system:
654 *
655 * o xhci_command_ring_t`xcr_lock
656 * o xhci_device_t`xd_imtx
657 *
658 * There is only one xcr_lock per controller, like the xhci_lock. It protects
659 * the state of the command ring. However, there is on xd_imtx per device.
660 * Recall that each device is scoped to a given controller. This protects the
661 * input slot context for a given device.
662 *
663 * There are a few important rules to keep in mind here that are true
664 * universally throughout the driver:
665 *
666 * 1) Always grab the xhci_t`xhci_lock, before grabbing any of the other locks.
667 * 2) A given xhci_device_t`xd_imtx, must be taken before grabbing the
668 * xhci_command_ring_t`xcr_lock.
669 * 3) A given thread can only hold one of the given xhci_device_t`xd_imtx locks
670 * at a given time. In other words, we should never be manipulating the input
671 * context of two different devices at once.
672 * 4) It is safe to hold the xhci_device_t`xd_imtx while tearing down the
673 * endpoint timer. Conversely, the endpoint specific logic should never enter
674 * this lock.
675 *
676 * --------------------
677 * Relationship to EHCI
678 * --------------------
679 *
680 * On some Intel chipsets, a given physical port on the system may be routed to
681 * one of the EHCI or xHCI controllers. This association can be dynamically
682 * changed by writing to platform specific registers as handled by the quirk
683 * logic in xhci_quirk.c.
684 *
685 * As these ports may support USB 3.x speeds, we always route all such ports to
686 * the xHCI controller, when supported. In addition, to minimize disruptions
687 * from devices being enumerated and attached to the EHCI driver and then
688 * disappearing, we generally attempt to load the xHCI controller before the
689 * EHCI controller. This logic is not done in the driver; however, it is done in
690 * other parts of the kernel like in uts/common/io/consconfig_dacf.c in the
691 * function consconfig_load_drivres().
692 *
693 * -----------
694 * Future Work
695 * -----------
696 *
697 * The primary future work in this driver spans two different, but related
698 * areas. The first area is around controller resets and how they tie into FM.
699 * Presently, we do not have a good way to handle controllers coming and going
700 * in the broader USB stack or properly reconfigure the device after a reset.
701 * Secondly, we don't handle the suspend and resume of devices and drivers.
702 */
703
704 #include <sys/param.h>
705 #include <sys/modctl.h>
706 #include <sys/conf.h>
707 #include <sys/devops.h>
708 #include <sys/ddi.h>
709 #include <sys/sunddi.h>
710 #include <sys/cmn_err.h>
711 #include <sys/ddifm.h>
712 #include <sys/pci.h>
713 #include <sys/class.h>
714 #include <sys/policy.h>
715
716 #include <sys/usb/hcd/xhci/xhci.h>
717 #include <sys/usb/hcd/xhci/xhci_ioctl.h>
718
719 /*
720 * We want to use the first BAR to access its registers. The regs[] array is
721 * ordered based on the rules for the PCI supplement to IEEE 1275. So regs[1]
722 * will always be the first BAR.
723 */
724 #define XHCI_REG_NUMBER 1
725
726 /*
727 * This task queue exists as a global taskq that is used for resetting the
728 * device in the face of FM or runtime errors. Each instance of the device
729 * (xhci_t) happens to have a single taskq_dispatch_ent already allocated so we
730 * know that we should always be able to dispatch such an event.
731 */
732 static taskq_t *xhci_taskq;
733
734 /*
735 * Global soft state for per-instance data. Note that we must use the soft state
736 * routines and cannot use the ddi_set_driver_private() routines. The USB
737 * framework presumes that it can use the dip's private data.
738 */
739 void *xhci_soft_state;
740
741 /*
742 * This is the time in us that we wait after a controller resets before we
743 * consider reading any register. There are some controllers that want at least
744 * 1 ms, therefore we default to 10 ms.
745 */
746 clock_t xhci_reset_delay = 10000;
747
748 void
749 xhci_error(xhci_t *xhcip, const char *fmt, ...)
750 {
751 va_list ap;
752
753 va_start(ap, fmt);
754 if (xhcip != NULL && xhcip->xhci_dip != NULL) {
755 vdev_err(xhcip->xhci_dip, CE_WARN, fmt, ap);
756 } else {
757 vcmn_err(CE_WARN, fmt, ap);
758 }
759 va_end(ap);
760 }
761
762 void
763 xhci_log(xhci_t *xhcip, const char *fmt, ...)
764 {
765 va_list ap;
766
767 va_start(ap, fmt);
768 if (xhcip != NULL && xhcip->xhci_dip != NULL) {
769 vdev_err(xhcip->xhci_dip, CE_NOTE, fmt, ap);
770 } else {
771 vcmn_err(CE_NOTE, fmt, ap);
772 }
773 va_end(ap);
774 }
775
776 /*
777 * USBA is in charge of creating device nodes for us. USBA explicitly ORs in the
778 * constant HUBD_IS_ROOT_HUB, so we have to undo that when we're looking at
779 * things here. A simple bitwise-and will take care of this. And hey, it could
780 * always be more complex, USBA could clone!
781 */
782 static dev_info_t *
783 xhci_get_dip(dev_t dev)
784 {
785 xhci_t *xhcip;
786 int instance = getminor(dev) & ~HUBD_IS_ROOT_HUB;
787
788 xhcip = ddi_get_soft_state(xhci_soft_state, instance);
789 if (xhcip != NULL)
790 return (xhcip->xhci_dip);
791 return (NULL);
792 }
793
794 uint8_t
795 xhci_get8(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off)
796 {
797 uintptr_t addr, roff;
798
799 switch (rtt) {
800 case XHCI_R_CAP:
801 roff = xhcip->xhci_regs_capoff;
802 break;
803 case XHCI_R_OPER:
804 roff = xhcip->xhci_regs_operoff;
805 break;
806 case XHCI_R_RUN:
807 roff = xhcip->xhci_regs_runoff;
808 break;
809 case XHCI_R_DOOR:
810 roff = xhcip->xhci_regs_dooroff;
811 break;
812 default:
813 panic("called %s with bad reg type: %d", __func__, rtt);
814 }
815 ASSERT(roff != PCI_EINVAL32);
816 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
817
818 return (ddi_get8(xhcip->xhci_regs_handle, (void *)addr));
819 }
820
821 uint16_t
822 xhci_get16(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off)
823 {
824 uintptr_t addr, roff;
825
826 switch (rtt) {
827 case XHCI_R_CAP:
828 roff = xhcip->xhci_regs_capoff;
829 break;
830 case XHCI_R_OPER:
831 roff = xhcip->xhci_regs_operoff;
832 break;
833 case XHCI_R_RUN:
834 roff = xhcip->xhci_regs_runoff;
835 break;
836 case XHCI_R_DOOR:
837 roff = xhcip->xhci_regs_dooroff;
838 break;
839 default:
840 panic("called %s with bad reg type: %d", __func__, rtt);
841 }
842 ASSERT(roff != PCI_EINVAL32);
843 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
844
845 return (ddi_get16(xhcip->xhci_regs_handle, (void *)addr));
846 }
847
848 uint32_t
849 xhci_get32(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off)
850 {
851 uintptr_t addr, roff;
852
853 switch (rtt) {
854 case XHCI_R_CAP:
855 roff = xhcip->xhci_regs_capoff;
856 break;
857 case XHCI_R_OPER:
858 roff = xhcip->xhci_regs_operoff;
859 break;
860 case XHCI_R_RUN:
861 roff = xhcip->xhci_regs_runoff;
862 break;
863 case XHCI_R_DOOR:
864 roff = xhcip->xhci_regs_dooroff;
865 break;
866 default:
867 panic("called %s with bad reg type: %d", __func__, rtt);
868 }
869 ASSERT(roff != PCI_EINVAL32);
870 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
871
872 return (ddi_get32(xhcip->xhci_regs_handle, (void *)addr));
873 }
874
875 uint64_t
876 xhci_get64(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off)
877 {
878 uintptr_t addr, roff;
879
880 switch (rtt) {
881 case XHCI_R_CAP:
882 roff = xhcip->xhci_regs_capoff;
883 break;
884 case XHCI_R_OPER:
885 roff = xhcip->xhci_regs_operoff;
886 break;
887 case XHCI_R_RUN:
888 roff = xhcip->xhci_regs_runoff;
889 break;
890 case XHCI_R_DOOR:
891 roff = xhcip->xhci_regs_dooroff;
892 break;
893 default:
894 panic("called %s with bad reg type: %d", __func__, rtt);
895 }
896 ASSERT(roff != PCI_EINVAL32);
897 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
898
899 return (ddi_get64(xhcip->xhci_regs_handle, (void *)addr));
900 }
901
902 void
903 xhci_put8(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off, uint8_t val)
904 {
905 uintptr_t addr, roff;
906
907 switch (rtt) {
908 case XHCI_R_CAP:
909 roff = xhcip->xhci_regs_capoff;
910 break;
911 case XHCI_R_OPER:
912 roff = xhcip->xhci_regs_operoff;
913 break;
914 case XHCI_R_RUN:
915 roff = xhcip->xhci_regs_runoff;
916 break;
917 case XHCI_R_DOOR:
918 roff = xhcip->xhci_regs_dooroff;
919 break;
920 default:
921 panic("called %s with bad reg type: %d", __func__, rtt);
922 }
923 ASSERT(roff != PCI_EINVAL32);
924 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
925
926 ddi_put8(xhcip->xhci_regs_handle, (void *)addr, val);
927 }
928
929 void
930 xhci_put16(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off, uint16_t val)
931 {
932 uintptr_t addr, roff;
933
934 switch (rtt) {
935 case XHCI_R_CAP:
936 roff = xhcip->xhci_regs_capoff;
937 break;
938 case XHCI_R_OPER:
939 roff = xhcip->xhci_regs_operoff;
940 break;
941 case XHCI_R_RUN:
942 roff = xhcip->xhci_regs_runoff;
943 break;
944 case XHCI_R_DOOR:
945 roff = xhcip->xhci_regs_dooroff;
946 break;
947 default:
948 panic("called %s with bad reg type: %d", __func__, rtt);
949 }
950 ASSERT(roff != PCI_EINVAL32);
951 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
952
953 ddi_put16(xhcip->xhci_regs_handle, (void *)addr, val);
954 }
955
956 void
957 xhci_put32(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off, uint32_t val)
958 {
959 uintptr_t addr, roff;
960
961 switch (rtt) {
962 case XHCI_R_CAP:
963 roff = xhcip->xhci_regs_capoff;
964 break;
965 case XHCI_R_OPER:
966 roff = xhcip->xhci_regs_operoff;
967 break;
968 case XHCI_R_RUN:
969 roff = xhcip->xhci_regs_runoff;
970 break;
971 case XHCI_R_DOOR:
972 roff = xhcip->xhci_regs_dooroff;
973 break;
974 default:
975 panic("called %s with bad reg type: %d", __func__, rtt);
976 }
977 ASSERT(roff != PCI_EINVAL32);
978 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
979
980 ddi_put32(xhcip->xhci_regs_handle, (void *)addr, val);
981 }
982
983 void
984 xhci_put64(xhci_t *xhcip, xhci_reg_type_t rtt, uintptr_t off, uint64_t val)
985 {
986 uintptr_t addr, roff;
987
988 switch (rtt) {
989 case XHCI_R_CAP:
990 roff = xhcip->xhci_regs_capoff;
991 break;
992 case XHCI_R_OPER:
993 roff = xhcip->xhci_regs_operoff;
994 break;
995 case XHCI_R_RUN:
996 roff = xhcip->xhci_regs_runoff;
997 break;
998 case XHCI_R_DOOR:
999 roff = xhcip->xhci_regs_dooroff;
1000 break;
1001 default:
1002 panic("called %s with bad reg type: %d", __func__, rtt);
1003 }
1004 ASSERT(roff != PCI_EINVAL32);
1005 addr = roff + off + (uintptr_t)xhcip->xhci_regs_base;
1006
1007 ddi_put64(xhcip->xhci_regs_handle, (void *)addr, val);
1008 }
1009
1010 int
1011 xhci_check_regs_acc(xhci_t *xhcip)
1012 {
1013 ddi_fm_error_t de;
1014
1015 /*
1016 * Treat the case where we can't check as fine so we can treat the code
1017 * more simply.
1018 */
1019 if (!DDI_FM_ACC_ERR_CAP(xhcip->xhci_fm_caps))
1020 return (DDI_FM_OK);
1021
1022 ddi_fm_acc_err_get(xhcip->xhci_regs_handle, &de, DDI_FME_VERSION);
1023 ddi_fm_acc_err_clear(xhcip->xhci_regs_handle, DDI_FME_VERSION);
1024 return (de.fme_status);
1025 }
1026
1027 /*
1028 * As a leaf PCIe driver, we just post the ereport and continue on.
1029 */
1030 /* ARGSUSED */
1031 static int
1032 xhci_fm_error_cb(dev_info_t *dip, ddi_fm_error_t *err, const void *impl_data)
1033 {
1034 pci_ereport_post(dip, err, NULL);
1035 return (err->fme_status);
1036 }
1037
1038 static void
1039 xhci_fm_fini(xhci_t *xhcip)
1040 {
1041 if (xhcip->xhci_fm_caps == 0)
1042 return;
1043
1044 if (DDI_FM_ERRCB_CAP(xhcip->xhci_fm_caps))
1045 ddi_fm_handler_unregister(xhcip->xhci_dip);
1046
1047 if (DDI_FM_EREPORT_CAP(xhcip->xhci_fm_caps) ||
1048 DDI_FM_ERRCB_CAP(xhcip->xhci_fm_caps))
1049 pci_ereport_teardown(xhcip->xhci_dip);
1050
1051 ddi_fm_fini(xhcip->xhci_dip);
1052 }
1053
1054 static void
1055 xhci_fm_init(xhci_t *xhcip)
1056 {
1057 ddi_iblock_cookie_t iblk;
1058 int def = DDI_FM_EREPORT_CAPABLE | DDI_FM_ACCCHK_CAPABLE |
1059 DDI_FM_DMACHK_CAPABLE | DDI_FM_ERRCB_CAPABLE;
1060
1061 xhcip->xhci_fm_caps = ddi_prop_get_int(DDI_DEV_T_ANY, xhcip->xhci_dip,
1062 DDI_PROP_DONTPASS, "fm_capable", def);
1063
1064 if (xhcip->xhci_fm_caps < 0) {
1065 xhcip->xhci_fm_caps = 0;
1066 } else if (xhcip->xhci_fm_caps & ~def) {
1067 xhcip->xhci_fm_caps &= def;
1068 }
1069
1070 if (xhcip->xhci_fm_caps == 0)
1071 return;
1072
1073 ddi_fm_init(xhcip->xhci_dip, &xhcip->xhci_fm_caps, &iblk);
1074 if (DDI_FM_EREPORT_CAP(xhcip->xhci_fm_caps) ||
1075 DDI_FM_ERRCB_CAP(xhcip->xhci_fm_caps)) {
1076 pci_ereport_setup(xhcip->xhci_dip);
1077 }
1078
1079 if (DDI_FM_ERRCB_CAP(xhcip->xhci_fm_caps)) {
1080 ddi_fm_handler_register(xhcip->xhci_dip,
1081 xhci_fm_error_cb, xhcip);
1082 }
1083 }
1084
1085 static int
1086 xhci_reg_poll(xhci_t *xhcip, xhci_reg_type_t rt, int reg, uint32_t mask,
1087 uint32_t targ, uint_t tries, int delay_ms)
1088 {
1089 uint_t i;
1090
1091 for (i = 0; i < tries; i++) {
1092 uint32_t val = xhci_get32(xhcip, rt, reg);
1093 if (!quiesce_active && xhci_check_regs_acc(xhcip)
1094 != DDI_FM_OK) {
1095 ddi_fm_service_impact(xhcip->xhci_dip,
1096 DDI_SERVICE_LOST);
1097 return (EIO);
1098 }
1099
1100 if ((val & mask) == targ)
1101 return (0);
1102
1103 delay(drv_usectohz(delay_ms * 1000));
1104 }
1105 return (ETIMEDOUT);
1106 }
1107
1108 static boolean_t
1109 xhci_regs_map(xhci_t *xhcip)
1110 {
1111 off_t memsize;
1112 int ret;
1113 ddi_device_acc_attr_t da;
1114
1115 if (ddi_dev_regsize(xhcip->xhci_dip, XHCI_REG_NUMBER, &memsize) !=
1116 DDI_SUCCESS) {
1117 xhci_error(xhcip, "failed to get register set size");
1118 return (B_FALSE);
1119 }
1120
1121 bzero(&da, sizeof (ddi_device_acc_attr_t));
1122 da.devacc_attr_version = DDI_DEVICE_ATTR_V0;
1123 da.devacc_attr_endian_flags = DDI_STRUCTURE_LE_ACC;
1124 da.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
1125 if (DDI_FM_ACC_ERR_CAP(xhcip->xhci_fm_caps)) {
1126 da.devacc_attr_access = DDI_FLAGERR_ACC;
1127 } else {
1128 da.devacc_attr_access = DDI_DEFAULT_ACC;
1129 }
1130
1131 ret = ddi_regs_map_setup(xhcip->xhci_dip, XHCI_REG_NUMBER,
1132 &xhcip->xhci_regs_base, 0, memsize, &da, &xhcip->xhci_regs_handle);
1133
1134 if (ret != DDI_SUCCESS) {
1135 xhci_error(xhcip, "failed to map device registers: %d", ret);
1136 return (B_FALSE);
1137 }
1138
1139 return (B_TRUE);
1140 }
1141
1142 static boolean_t
1143 xhci_regs_init(xhci_t *xhcip)
1144 {
1145 /*
1146 * The capabilities always begin at offset zero.
1147 */
1148 xhcip->xhci_regs_capoff = 0;
1149 xhcip->xhci_regs_operoff = xhci_get8(xhcip, XHCI_R_CAP, XHCI_CAPLENGTH);
1150 xhcip->xhci_regs_runoff = xhci_get32(xhcip, XHCI_R_CAP, XHCI_RTSOFF);
1151 xhcip->xhci_regs_runoff &= ~0x1f;
1152 xhcip->xhci_regs_dooroff = xhci_get32(xhcip, XHCI_R_CAP, XHCI_DBOFF);
1153 xhcip->xhci_regs_dooroff &= ~0x3;
1154
1155 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1156 xhci_error(xhcip, "failed to initialize controller register "
1157 "offsets: encountered FM register error");
1158 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1159 return (B_FALSE);
1160 }
1161
1162 return (B_TRUE);
1163 }
1164
1165 /*
1166 * Read various parameters from PCI configuration space and from the Capability
1167 * registers that we'll need to register the device. We cache all of the
1168 * Capability registers.
1169 */
1170 static boolean_t
1171 xhci_read_params(xhci_t *xhcip)
1172 {
1173 uint8_t usb;
1174 uint16_t vers;
1175 uint32_t struc1, struc2, struc3, cap1, cap2, pgsz;
1176 uint32_t psize, pbit, capreg;
1177 xhci_capability_t *xcap;
1178 unsigned long ps;
1179
1180 /*
1181 * While it's tempting to do a 16-bit read at offset 0x2, unfortunately,
1182 * a few emulated systems don't support reading at offset 0x2 for the
1183 * version. Instead we need to read the caplength register and get the
1184 * upper two bytes.
1185 */
1186 capreg = xhci_get32(xhcip, XHCI_R_CAP, XHCI_CAPLENGTH);
1187 vers = XHCI_VERSION_MASK(capreg);
1188 usb = pci_config_get8(xhcip->xhci_cfg_handle, PCI_XHCI_USBREV);
1189 struc1 = xhci_get32(xhcip, XHCI_R_CAP, XHCI_HCSPARAMS1);
1190 struc2 = xhci_get32(xhcip, XHCI_R_CAP, XHCI_HCSPARAMS2);
1191 struc3 = xhci_get32(xhcip, XHCI_R_CAP, XHCI_HCSPARAMS3);
1192 cap1 = xhci_get32(xhcip, XHCI_R_CAP, XHCI_HCCPARAMS1);
1193 cap2 = xhci_get32(xhcip, XHCI_R_CAP, XHCI_HCCPARAMS2);
1194 pgsz = xhci_get32(xhcip, XHCI_R_OPER, XHCI_PAGESIZE);
1195 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1196 xhci_error(xhcip, "failed to read controller parameters: "
1197 "encountered FM register error");
1198 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1199 return (B_FALSE);
1200 }
1201
1202 xcap = &xhcip->xhci_caps;
1203 xcap->xcap_usb_vers = usb;
1204 xcap->xcap_hci_vers = vers;
1205 xcap->xcap_max_slots = XHCI_HCS1_DEVSLOT_MAX(struc1);
1206 xcap->xcap_max_intrs = XHCI_HCS1_IRQ_MAX(struc1);
1207 xcap->xcap_max_ports = XHCI_HCS1_N_PORTS(struc1);
1208 if (xcap->xcap_max_ports > MAX_PORTS) {
1209 xhci_error(xhcip, "Root hub has %d ports, but system only "
1210 "supports %d, limiting to %d\n", xcap->xcap_max_ports,
1211 MAX_PORTS, MAX_PORTS);
1212 xcap->xcap_max_ports = MAX_PORTS;
1213 }
1214
1215 xcap->xcap_ist_micro = XHCI_HCS2_IST_MICRO(struc2);
1216 xcap->xcap_ist = XHCI_HCS2_IST(struc2);
1217 xcap->xcap_max_esrt = XHCI_HCS2_ERST_MAX(struc2);
1218 xcap->xcap_scratch_restore = XHCI_HCS2_SPR(struc2);
1219 xcap->xcap_max_scratch = XHCI_HCS2_SPB_MAX(struc2);
1220
1221 xcap->xcap_u1_lat = XHCI_HCS3_U1_DEL(struc3);
1222 xcap->xcap_u2_lat = XHCI_HCS3_U2_DEL(struc3);
1223
1224 xcap->xcap_flags = XHCI_HCC1_FLAGS_MASK(cap1);
1225 xcap->xcap_max_psa = XHCI_HCC1_PSA_SZ_MAX(cap1);
1226 xcap->xcap_xecp_off = XHCI_HCC1_XECP(cap1);
1227 xcap->xcap_flags2 = XHCI_HCC2_FLAGS_MASK(cap2);
1228
1229 /*
1230 * We don't have documentation for what changed from before xHCI 0.96,
1231 * so we just refuse to support versions before 0.96. We also will
1232 * ignore anything with a major version greater than 1.
1233 */
1234 if (xcap->xcap_hci_vers < 0x96 || xcap->xcap_hci_vers >= 0x200) {
1235 xhci_error(xhcip, "Encountered unsupported xHCI version 0.%2x",
1236 xcap->xcap_hci_vers);
1237 return (B_FALSE);
1238 }
1239
1240 /*
1241 * Determine the smallest size page that the controller supports and
1242 * make sure that it matches our pagesize. We basically check here for
1243 * the presence of 4k and 8k pages. The basis of the pagesize is used
1244 * extensively throughout the code and specification. While we could
1245 * support other page sizes here, given that we don't support systems
1246 * with it at this time, it doesn't make much sense.
1247 */
1248 ps = PAGESIZE;
1249 if (ps == 0x1000) {
1250 pbit = XHCI_PAGESIZE_4K;
1251 psize = 0x1000;
1252 } else if (ps == 0x2000) {
1253 pbit = XHCI_PAGESIZE_8K;
1254 psize = 0x2000;
1255 } else {
1256 xhci_error(xhcip, "Encountered host page size that the driver "
1257 "doesn't know how to handle: %lx\n", ps);
1258 return (B_FALSE);
1259 }
1260
1261 if (!(pgsz & pbit)) {
1262 xhci_error(xhcip, "Encountered controller that didn't support "
1263 "the host page size (%d), supports: %x", psize, pgsz);
1264 return (B_FALSE);
1265 }
1266 xcap->xcap_pagesize = psize;
1267
1268 return (B_TRUE);
1269 }
1270
1271 /*
1272 * Apply known workarounds and issues. These reports come from other
1273 * Operating Systems and have been collected over time.
1274 */
1275 static boolean_t
1276 xhci_identify(xhci_t *xhcip)
1277 {
1278 xhci_quirks_populate(xhcip);
1279
1280 if (xhcip->xhci_quirks & XHCI_QUIRK_NO_MSI) {
1281 xhcip->xhci_caps.xcap_intr_types = DDI_INTR_TYPE_FIXED;
1282 } else {
1283 xhcip->xhci_caps.xcap_intr_types = DDI_INTR_TYPE_FIXED |
1284 DDI_INTR_TYPE_MSI | DDI_INTR_TYPE_MSIX;
1285 }
1286
1287 if (xhcip->xhci_quirks & XHCI_QUIRK_32_ONLY) {
1288 xhcip->xhci_caps.xcap_flags &= ~XCAP_AC64;
1289 }
1290
1291 return (B_TRUE);
1292 }
1293
1294 static boolean_t
1295 xhci_alloc_intr_handle(xhci_t *xhcip, int type)
1296 {
1297 int ret;
1298
1299 /*
1300 * Normally a well-behaving driver would more carefully request an
1301 * amount of interrupts based on the number available, etc. But since we
1302 * only actually want a single interrupt, we're just going to go ahead
1303 * and ask for a single interrupt.
1304 */
1305 ret = ddi_intr_alloc(xhcip->xhci_dip, &xhcip->xhci_intr_hdl, type, 0,
1306 XHCI_NINTR, &xhcip->xhci_intr_num, DDI_INTR_ALLOC_NORMAL);
1307 if (ret != DDI_SUCCESS) {
1308 xhci_log(xhcip, "!failed to allocate interrupts of type %d: %d",
1309 type, ret);
1310 return (B_FALSE);
1311 }
1312 xhcip->xhci_intr_type = type;
1313
1314 return (B_TRUE);
1315 }
1316
1317 static boolean_t
1318 xhci_alloc_intrs(xhci_t *xhcip)
1319 {
1320 int intr_types, ret;
1321
1322 if (XHCI_NINTR > xhcip->xhci_caps.xcap_max_intrs) {
1323 xhci_error(xhcip, "controller does not support the minimum "
1324 "number of interrupts required (%d), supports %d",
1325 XHCI_NINTR, xhcip->xhci_caps.xcap_max_intrs);
1326 return (B_FALSE);
1327 }
1328
1329 if ((ret = ddi_intr_get_supported_types(xhcip->xhci_dip,
1330 &intr_types)) != DDI_SUCCESS) {
1331 xhci_error(xhcip, "failed to get supported interrupt types: "
1332 "%d", ret);
1333 return (B_FALSE);
1334 }
1335
1336 /*
1337 * Mask off interrupt types we've already ruled out due to quirks or
1338 * other reasons.
1339 */
1340 intr_types &= xhcip->xhci_caps.xcap_intr_types;
1341 if (intr_types & DDI_INTR_TYPE_MSIX) {
1342 if (xhci_alloc_intr_handle(xhcip, DDI_INTR_TYPE_MSIX))
1343 return (B_TRUE);
1344 }
1345
1346 if (intr_types & DDI_INTR_TYPE_MSI) {
1347 if (xhci_alloc_intr_handle(xhcip, DDI_INTR_TYPE_MSI))
1348 return (B_TRUE);
1349 }
1350
1351 if (intr_types & DDI_INTR_TYPE_FIXED) {
1352 if (xhci_alloc_intr_handle(xhcip, DDI_INTR_TYPE_FIXED))
1353 return (B_TRUE);
1354 }
1355
1356 xhci_error(xhcip, "failed to allocate an interrupt, supported types: "
1357 "0x%x", intr_types);
1358 return (B_FALSE);
1359 }
1360
1361 static boolean_t
1362 xhci_add_intr_handler(xhci_t *xhcip)
1363 {
1364 int ret;
1365
1366 if ((ret = ddi_intr_get_pri(xhcip->xhci_intr_hdl,
1367 &xhcip->xhci_intr_pri)) != DDI_SUCCESS) {
1368 xhci_error(xhcip, "failed to get interrupt priority: %d", ret);
1369 return (B_FALSE);
1370 }
1371
1372 if ((ret = ddi_intr_get_cap(xhcip->xhci_intr_hdl,
1373 &xhcip->xhci_intr_caps)) != DDI_SUCCESS) {
1374 xhci_error(xhcip, "failed to get interrupt capabilities: %d",
1375 ret);
1376 return (B_FALSE);
1377 }
1378
1379 if ((ret = ddi_intr_add_handler(xhcip->xhci_intr_hdl, xhci_intr, xhcip,
1380 (uintptr_t)0)) != DDI_SUCCESS) {
1381 xhci_error(xhcip, "failed to add interrupt handler: %d", ret);
1382 return (B_FALSE);
1383 }
1384 return (B_TRUE);
1385 }
1386
1387 /*
1388 * Find a capability with an identifier whose value is 'id'. The 'init' argument
1389 * gives us the offset to start searching at. See xHCI 1.1 / 7 for more
1390 * information. This is more or less exactly like PCI capabilities.
1391 */
1392 static boolean_t
1393 xhci_find_ext_cap(xhci_t *xhcip, uint32_t id, uint32_t init, uint32_t *outp)
1394 {
1395 uint32_t off;
1396 uint8_t next = 0;
1397
1398 /*
1399 * If we have no offset, we're done.
1400 */
1401 if (xhcip->xhci_caps.xcap_xecp_off == 0)
1402 return (B_FALSE);
1403
1404 off = xhcip->xhci_caps.xcap_xecp_off << 2;
1405 do {
1406 uint32_t cap_hdr;
1407
1408 off += next << 2;
1409 cap_hdr = xhci_get32(xhcip, XHCI_R_CAP, off);
1410 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1411 xhci_error(xhcip, "failed to read xhci extended "
1412 "capabilities at offset 0x%x: encountered FM "
1413 "register error", off);
1414 ddi_fm_service_impact(xhcip->xhci_dip,
1415 DDI_SERVICE_LOST);
1416 break;
1417 }
1418
1419 if (cap_hdr == PCI_EINVAL32)
1420 break;
1421 if (XHCI_XECP_ID(cap_hdr) == id &&
1422 (init == UINT32_MAX || off > init)) {
1423 *outp = off;
1424 return (B_TRUE);
1425 }
1426 next = XHCI_XECP_NEXT(cap_hdr);
1427 /*
1428 * Watch out for overflow if we somehow end up with a more than
1429 * 2 GiB space.
1430 */
1431 if (next << 2 > (INT32_MAX - off))
1432 return (B_FALSE);
1433 } while (next != 0);
1434
1435 return (B_FALSE);
1436 }
1437
1438 /*
1439 * For mostly information purposes, we'd like to walk to augment the devinfo
1440 * tree with the number of ports that support USB 2 and USB 3. Note though that
1441 * these ports may be overlapping. Many ports can support both USB 2 and USB 3
1442 * and are wired up to the same physical port, even though they show up as
1443 * separate 'ports' in the xhci sense.
1444 */
1445 static boolean_t
1446 xhci_port_count(xhci_t *xhcip)
1447 {
1448 uint_t nusb2 = 0, nusb3 = 0;
1449 uint32_t off = UINT32_MAX;
1450
1451 while (xhci_find_ext_cap(xhcip, XHCI_ID_PROTOCOLS, off, &off) ==
1452 B_TRUE) {
1453 uint32_t rvers, rport;
1454
1455 /*
1456 * See xHCI 1.1 / 7.2 for the format of this. The first uint32_t
1457 * has version information while the third uint32_t has the port
1458 * count.
1459 */
1460 rvers = xhci_get32(xhcip, XHCI_R_CAP, off);
1461 rport = xhci_get32(xhcip, XHCI_R_CAP, off + 8);
1462 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1463 xhci_error(xhcip, "failed to read xhci port counts: "
1464 "encountered fatal FM register error");
1465 ddi_fm_service_impact(xhcip->xhci_dip,
1466 DDI_SERVICE_LOST);
1467 return (B_FALSE);
1468 }
1469
1470 rvers = XHCI_XECP_PROT_MAJOR(rvers);
1471 rport = XHCI_XECP_PROT_PCOUNT(rport);
1472
1473 if (rvers == 3) {
1474 nusb3 += rport;
1475 } else if (rvers <= 2) {
1476 nusb2 += rport;
1477 } else {
1478 xhci_error(xhcip, "encountered port capabilities with "
1479 "unknown major USB version: %d\n", rvers);
1480 }
1481 }
1482
1483 (void) ddi_prop_update_int(DDI_DEV_T_NONE, xhcip->xhci_dip,
1484 "usb2-capable-ports", nusb2);
1485 (void) ddi_prop_update_int(DDI_DEV_T_NONE, xhcip->xhci_dip,
1486 "usb3-capable-ports", nusb3);
1487
1488 return (B_TRUE);
1489 }
1490
1491 /*
1492 * Take over control from the BIOS or other firmware, if applicable.
1493 */
1494 static boolean_t
1495 xhci_controller_takeover(xhci_t *xhcip)
1496 {
1497 int ret;
1498 uint32_t val, off;
1499
1500 /*
1501 * If we can't find the legacy capability, then there's nothing to do.
1502 */
1503 if (xhci_find_ext_cap(xhcip, XHCI_ID_USB_LEGACY, UINT32_MAX, &off) ==
1504 B_FALSE)
1505 return (B_TRUE);
1506 val = xhci_get32(xhcip, XHCI_R_CAP, off);
1507 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1508 xhci_error(xhcip, "failed to read BIOS take over registers: "
1509 "encountered fatal FM register error");
1510 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1511 return (B_FALSE);
1512 }
1513
1514 if (val & XHCI_BIOS_OWNED) {
1515 val |= XHCI_OS_OWNED;
1516 xhci_put32(xhcip, XHCI_R_CAP, off, val);
1517 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1518 xhci_error(xhcip, "failed to write BIOS take over "
1519 "registers: encountered fatal FM register error");
1520 ddi_fm_service_impact(xhcip->xhci_dip,
1521 DDI_SERVICE_LOST);
1522 return (B_FALSE);
1523 }
1524
1525 /*
1526 * Wait up to 5 seconds for things to change. While this number
1527 * isn't specified in the xHCI spec, it seems to be the de facto
1528 * value that various systems are using today. We'll use a 10ms
1529 * interval to check.
1530 */
1531 ret = xhci_reg_poll(xhcip, XHCI_R_CAP, off,
1532 XHCI_BIOS_OWNED | XHCI_OS_OWNED, XHCI_OS_OWNED, 500, 10);
1533 if (ret == EIO)
1534 return (B_FALSE);
1535 if (ret == ETIMEDOUT) {
1536 xhci_log(xhcip, "!timed out waiting for firmware to "
1537 "hand off, taking over");
1538 val &= ~XHCI_BIOS_OWNED;
1539 xhci_put32(xhcip, XHCI_R_CAP, off, val);
1540 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1541 xhci_error(xhcip, "failed to write forced "
1542 "takeover: encountered fatal FM register "
1543 "error");
1544 ddi_fm_service_impact(xhcip->xhci_dip,
1545 DDI_SERVICE_LOST);
1546 return (B_FALSE);
1547 }
1548 }
1549 }
1550
1551 val = xhci_get32(xhcip, XHCI_R_CAP, off + XHCI_XECP_LEGCTLSTS);
1552 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1553 xhci_error(xhcip, "failed to read legacy control registers: "
1554 "encountered fatal FM register error");
1555 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1556 return (B_FALSE);
1557 }
1558 val &= XHCI_XECP_SMI_MASK;
1559 val |= XHCI_XECP_CLEAR_SMI;
1560 xhci_put32(xhcip, XHCI_R_CAP, off + XHCI_XECP_LEGCTLSTS, val);
1561 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1562 xhci_error(xhcip, "failed to write legacy control registers: "
1563 "encountered fatal FM register error");
1564 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1565 return (B_FALSE);
1566 }
1567
1568 return (B_TRUE);
1569 }
1570
1571 static int
1572 xhci_controller_stop(xhci_t *xhcip)
1573 {
1574 uint32_t cmdreg;
1575
1576 cmdreg = xhci_get32(xhcip, XHCI_R_OPER, XHCI_USBCMD);
1577 if (!quiesce_active && xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1578 xhci_error(xhcip, "failed to read USB Command register: "
1579 "encountered fatal FM register error");
1580 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1581 return (EIO);
1582 }
1583
1584 cmdreg &= ~(XHCI_CMD_RS | XHCI_CMD_INTE);
1585 xhci_put32(xhcip, XHCI_R_OPER, XHCI_USBCMD, cmdreg);
1586 if (!quiesce_active && xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1587 xhci_error(xhcip, "failed to write USB Command register: "
1588 "encountered fatal FM register error");
1589 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1590 return (EIO);
1591 }
1592
1593 /*
1594 * Wait up to 50ms for this to occur. The specification says that this
1595 * should stop within 16ms, but we give ourselves a bit more time just
1596 * in case.
1597 */
1598 return (xhci_reg_poll(xhcip, XHCI_R_OPER, XHCI_USBSTS, XHCI_STS_HCH,
1599 XHCI_STS_HCH, 50, 10));
1600 }
1601
1602 static int
1603 xhci_controller_reset(xhci_t *xhcip)
1604 {
1605 int ret;
1606 uint32_t cmdreg;
1607
1608 cmdreg = xhci_get32(xhcip, XHCI_R_OPER, XHCI_USBCMD);
1609 if (!quiesce_active && xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1610 xhci_error(xhcip, "failed to read USB Command register for "
1611 "reset: encountered fatal FM register error");
1612 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1613 return (EIO);
1614 }
1615
1616 cmdreg |= XHCI_CMD_HCRST;
1617 xhci_put32(xhcip, XHCI_R_OPER, XHCI_USBCMD, cmdreg);
1618 if (!quiesce_active && xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1619 xhci_error(xhcip, "failed to write USB Command register for "
1620 "reset: encountered fatal FM register error");
1621 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1622 return (EIO);
1623 }
1624
1625 /*
1626 * Some controllers apparently don't want to be touched for at least 1ms
1627 * after we initiate the reset. Therefore give all controllers this
1628 * moment to breathe.
1629 */
1630 delay(drv_usectohz(xhci_reset_delay));
1631
1632 /*
1633 * To tell that the reset has completed we first verify that the reset
1634 * has finished and that the USBCMD register no longer has the reset bit
1635 * asserted. However, once that's done we have to go verify that CNR
1636 * (Controller Not Ready) is no longer asserted.
1637 */
1638 if ((ret = xhci_reg_poll(xhcip, XHCI_R_OPER, XHCI_USBCMD,
1639 XHCI_CMD_HCRST, 0, 500, 10)) != 0)
1640 return (ret);
1641
1642 return (xhci_reg_poll(xhcip, XHCI_R_OPER, XHCI_USBSTS,
1643 XHCI_STS_CNR, 0, 500, 10));
1644 }
1645
1646 /*
1647 * Take care of all the required initialization before we can actually enable
1648 * the controller. This means that we need to:
1649 *
1650 * o Program the maximum number of slots
1651 * o Program the DCBAAP and allocate the scratchpad
1652 * o Program the Command Ring
1653 * o Initialize the Event Ring
1654 * o Enable interrupts (set imod)
1655 */
1656 static int
1657 xhci_controller_configure(xhci_t *xhcip)
1658 {
1659 int ret;
1660 uint32_t config;
1661
1662 config = xhci_get32(xhcip, XHCI_R_OPER, XHCI_CONFIG);
1663 config &= ~XHCI_CONFIG_SLOTS_MASK;
1664 config |= xhcip->xhci_caps.xcap_max_slots;
1665 xhci_put32(xhcip, XHCI_R_OPER, XHCI_CONFIG, config);
1666 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1667 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1668 return (EIO);
1669 }
1670
1671 if ((ret = xhci_context_init(xhcip)) != 0) {
1672 const char *reason;
1673 if (ret == EIO) {
1674 reason = "fatal FM I/O error occurred";
1675 } else if (ret == ENOMEM) {
1676 reason = "unable to allocate DMA memory";
1677 } else {
1678 reason = "unexpected error occurred";
1679 }
1680
1681 xhci_error(xhcip, "failed to initialize xhci context "
1682 "registers: %s (%d)", reason, ret);
1683 return (ret);
1684 }
1685
1686 if ((ret = xhci_command_ring_init(xhcip)) != 0) {
1687 xhci_error(xhcip, "failed to initialize commands: %d", ret);
1688 return (ret);
1689 }
1690
1691 if ((ret = xhci_event_init(xhcip)) != 0) {
1692 xhci_error(xhcip, "failed to initialize events: %d", ret);
1693 return (ret);
1694 }
1695
1696 if ((ret = xhci_intr_conf(xhcip)) != 0) {
1697 xhci_error(xhcip, "failed to configure interrupts: %d", ret);
1698 return (ret);
1699 }
1700
1701 return (0);
1702 }
1703
1704 static int
1705 xhci_controller_start(xhci_t *xhcip)
1706 {
1707 uint32_t reg;
1708
1709 reg = xhci_get32(xhcip, XHCI_R_OPER, XHCI_USBCMD);
1710 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1711 xhci_error(xhcip, "failed to read USB Command register for "
1712 "start: encountered fatal FM register error");
1713 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1714 return (EIO);
1715 }
1716
1717 reg |= XHCI_CMD_RS;
1718 xhci_put32(xhcip, XHCI_R_OPER, XHCI_USBCMD, reg);
1719 if (xhci_check_regs_acc(xhcip) != DDI_FM_OK) {
1720 xhci_error(xhcip, "failed to write USB Command register for "
1721 "start: encountered fatal FM register error");
1722 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1723 return (EIO);
1724 }
1725
1726 return (xhci_reg_poll(xhcip, XHCI_R_OPER, XHCI_USBSTS,
1727 XHCI_STS_HCH, 0, 500, 10));
1728 }
1729
1730 /* ARGSUSED */
1731 static void
1732 xhci_reset_task(void *arg)
1733 {
1734 /*
1735 * Longer term, we'd like to properly perform a controller reset.
1736 * However, that requires a bit more assistance from USBA to work
1737 * properly and tear down devices. In the meantime, we panic.
1738 */
1739 panic("XHCI runtime reset required");
1740 }
1741
1742 /*
1743 * This function is called when we've detected a fatal FM condition that has
1744 * resulted in a loss of service and we need to force a reset of the controller
1745 * as a whole. Only one such reset may be ongoing at a time.
1746 */
1747 void
1748 xhci_fm_runtime_reset(xhci_t *xhcip)
1749 {
1750 boolean_t locked = B_FALSE;
1751
1752 if (mutex_owned(&xhcip->xhci_lock)) {
1753 locked = B_TRUE;
1754 } else {
1755 mutex_enter(&xhcip->xhci_lock);
1756 }
1757
1758 /*
1759 * If we're already in the error state than a reset is already ongoing
1760 * and there is nothing for us to do here.
1761 */
1762 if (xhcip->xhci_state & XHCI_S_ERROR) {
1763 goto out;
1764 }
1765
1766 xhcip->xhci_state |= XHCI_S_ERROR;
1767 ddi_fm_service_impact(xhcip->xhci_dip, DDI_SERVICE_LOST);
1768 taskq_dispatch_ent(xhci_taskq, xhci_reset_task, xhcip, 0,
1769 &xhcip->xhci_tqe);
1770 out:
1771 if (!locked) {
1772 mutex_exit(&xhcip->xhci_lock);
1773 }
1774 }
1775
1776 static int
1777 xhci_ioctl_portsc(xhci_t *xhcip, intptr_t arg)
1778 {
1779 int i;
1780 xhci_ioctl_portsc_t xhi;
1781
1782 bzero(&xhi, sizeof (xhci_ioctl_portsc_t));
1783 xhi.xhi_nports = xhcip->xhci_caps.xcap_max_ports;
1784 for (i = 1; i <= xhcip->xhci_caps.xcap_max_ports; i++) {
1785 xhi.xhi_portsc[i] = xhci_get32(xhcip, XHCI_R_OPER,
1786 XHCI_PORTSC(i));
1787 }
1788
1789 if (ddi_copyout(&xhi, (void *)(uintptr_t)arg, sizeof (xhi), 0) != 0)
1790 return (EFAULT);
1791
1792 return (0);
1793 }
1794
1795 static int
1796 xhci_ioctl_clear(xhci_t *xhcip, intptr_t arg)
1797 {
1798 uint32_t reg;
1799 xhci_ioctl_clear_t xic;
1800
1801 if (ddi_copyin((const void *)(uintptr_t)arg, &xic, sizeof (xic),
1802 0) != 0)
1803 return (EFAULT);
1804
1805 if (xic.xic_port == 0 || xic.xic_port >
1806 xhcip->xhci_caps.xcap_max_ports)
1807 return (EINVAL);
1808
1809 reg = xhci_get32(xhcip, XHCI_R_OPER, XHCI_PORTSC(xic.xic_port));
1810 reg &= ~XHCI_PS_CLEAR;
1811 reg |= XHCI_PS_CSC | XHCI_PS_PEC | XHCI_PS_WRC | XHCI_PS_OCC |
1812 XHCI_PS_PRC | XHCI_PS_PLC | XHCI_PS_CEC;
1813 xhci_put32(xhcip, XHCI_R_OPER, XHCI_PORTSC(xic.xic_port), reg);
1814
1815 return (0);
1816 }
1817
1818 static int
1819 xhci_ioctl_setpls(xhci_t *xhcip, intptr_t arg)
1820 {
1821 uint32_t reg;
1822 xhci_ioctl_setpls_t xis;
1823
1824 if (ddi_copyin((const void *)(uintptr_t)arg, &xis, sizeof (xis),
1825 0) != 0)
1826 return (EFAULT);
1827
1828 if (xis.xis_port == 0 || xis.xis_port >
1829 xhcip->xhci_caps.xcap_max_ports)
1830 return (EINVAL);
1831
1832 if (xis.xis_pls & ~0xf)
1833 return (EINVAL);
1834
1835 reg = xhci_get32(xhcip, XHCI_R_OPER, XHCI_PORTSC(xis.xis_port));
1836 reg &= ~XHCI_PS_CLEAR;
1837 reg |= XHCI_PS_PLS_SET(xis.xis_pls);
1838 reg |= XHCI_PS_LWS;
1839 xhci_put32(xhcip, XHCI_R_OPER, XHCI_PORTSC(xis.xis_port), reg);
1840
1841 return (0);
1842 }
1843
1844 static int
1845 xhci_open(dev_t *devp, int flags, int otyp, cred_t *credp)
1846 {
1847 dev_info_t *dip = xhci_get_dip(*devp);
1848
1849 return (usba_hubdi_open(dip, devp, flags, otyp, credp));
1850 }
1851
1852 static int
1853 xhci_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *credp,
1854 int *rvalp)
1855 {
1856 dev_info_t *dip = xhci_get_dip(dev);
1857
1858 if (cmd == XHCI_IOCTL_PORTSC ||
1859 cmd == XHCI_IOCTL_CLEAR ||
1860 cmd == XHCI_IOCTL_SETPLS) {
1861 xhci_t *xhcip = ddi_get_soft_state(xhci_soft_state,
1862 getminor(dev) & ~HUBD_IS_ROOT_HUB);
1863
1864 if (secpolicy_xhci(credp) != 0 ||
1865 crgetzoneid(credp) != GLOBAL_ZONEID)
1866 return (EPERM);
1867
1868 if (mode & FKIOCTL)
1869 return (ENOTSUP);
1870
1871 if (!(mode & FWRITE))
1872 return (EBADF);
1873
1874 if (cmd == XHCI_IOCTL_PORTSC)
1875 return (xhci_ioctl_portsc(xhcip, arg));
1876 else if (cmd == XHCI_IOCTL_CLEAR)
1877 return (xhci_ioctl_clear(xhcip, arg));
1878 else
1879 return (xhci_ioctl_setpls(xhcip, arg));
1880 }
1881
1882 return (usba_hubdi_ioctl(dip, dev, cmd, arg, mode, credp, rvalp));
1883 }
1884
1885 static int
1886 xhci_close(dev_t dev, int flag, int otyp, cred_t *credp)
1887 {
1888 dev_info_t *dip = xhci_get_dip(dev);
1889
1890 return (usba_hubdi_close(dip, dev, flag, otyp, credp));
1891 }
1892
1893 /*
1894 * We try to clean up everything that we can. The only thing that we let stop us
1895 * at this time is a failure to remove the root hub, which is realistically the
1896 * equivalent of our EBUSY case.
1897 */
1898 static int
1899 xhci_cleanup(xhci_t *xhcip)
1900 {
1901 int ret, inst;
1902
1903 if (xhcip->xhci_seq & XHCI_ATTACH_ROOT_HUB) {
1904 if ((ret = xhci_root_hub_fini(xhcip)) != 0)
1905 return (ret);
1906 }
1907
1908 if (xhcip->xhci_seq & XHCI_ATTACH_USBA) {
1909 xhci_hcd_fini(xhcip);
1910 }
1911
1912 if (xhcip->xhci_seq & XHCI_ATTACH_STARTED) {
1913 mutex_enter(&xhcip->xhci_lock);
1914 while (xhcip->xhci_state & XHCI_S_ERROR)
1915 cv_wait(&xhcip->xhci_statecv, &xhcip->xhci_lock);
1916 mutex_exit(&xhcip->xhci_lock);
1917
1918 (void) xhci_controller_stop(xhcip);
1919 }
1920
1921 /*
1922 * Always release the context, command, and event data. They handle the
1923 * fact that they me be in an arbitrary state or unallocated.
1924 */
1925 xhci_event_fini(xhcip);
1926 xhci_command_ring_fini(xhcip);
1927 xhci_context_fini(xhcip);
1928
1929 if (xhcip->xhci_seq & XHCI_ATTACH_INTR_ENABLE) {
1930 (void) xhci_ddi_intr_disable(xhcip);
1931 }
1932
1933 if (xhcip->xhci_seq & XHCI_ATTACH_SYNCH) {
1934 cv_destroy(&xhcip->xhci_statecv);
1935 mutex_destroy(&xhcip->xhci_lock);
1936 }
1937
1938 if (xhcip->xhci_seq & XHCI_ATTACH_INTR_ADD) {
1939 if ((ret = ddi_intr_remove_handler(xhcip->xhci_intr_hdl)) !=
1940 DDI_SUCCESS) {
1941 xhci_error(xhcip, "failed to remove interrupt "
1942 "handler: %d", ret);
1943 }
1944 }
1945
1946 if (xhcip->xhci_seq & XHCI_ATTACH_INTR_ALLOC) {
1947 if ((ret = ddi_intr_free(xhcip->xhci_intr_hdl)) !=
1948 DDI_SUCCESS) {
1949 xhci_error(xhcip, "failed to free interrupts: %d", ret);
1950 }
1951 }
1952
1953 if (xhcip->xhci_seq & XHCI_ATTACH_REGS_MAP) {
1954 ddi_regs_map_free(&xhcip->xhci_regs_handle);
1955 xhcip->xhci_regs_handle = NULL;
1956 }
1957
1958 if (xhcip->xhci_seq & XHCI_ATTACH_PCI_CONFIG) {
1959 pci_config_teardown(&xhcip->xhci_cfg_handle);
1960 xhcip->xhci_cfg_handle = NULL;
1961 }
1962
1963 if (xhcip->xhci_seq & XHCI_ATTACH_FM) {
1964 xhci_fm_fini(xhcip);
1965 xhcip->xhci_fm_caps = 0;
1966 }
1967
1968 inst = ddi_get_instance(xhcip->xhci_dip);
1969 xhcip->xhci_dip = NULL;
1970 ddi_soft_state_free(xhci_soft_state, inst);
1971
1972 return (DDI_SUCCESS);
1973 }
1974
1975 /* QUIESCE(9E) to support fast reboot */
1976 int
1977 xhci_quiesce(dev_info_t *dip)
1978 {
1979 xhci_t *xhcip;
1980
1981 xhcip = ddi_get_soft_state(xhci_soft_state, ddi_get_instance(dip));
1982
1983 return (xhci_controller_stop(xhcip) == 0 &&
1984 xhci_controller_reset(xhcip) == 0 ? DDI_SUCCESS : DDI_FAILURE);
1985 }
1986
1987 static int
1988 xhci_attach(dev_info_t *dip, ddi_attach_cmd_t cmd)
1989 {
1990 int ret, inst, route;
1991 xhci_t *xhcip;
1992
1993 if (cmd != DDI_ATTACH)
1994 return (DDI_FAILURE);
1995
1996 inst = ddi_get_instance(dip);
1997 if (ddi_soft_state_zalloc(xhci_soft_state, inst) != 0)
1998 return (DDI_FAILURE);
1999 xhcip = ddi_get_soft_state(xhci_soft_state, ddi_get_instance(dip));
2000 xhcip->xhci_dip = dip;
2001
2002 xhcip->xhci_regs_capoff = PCI_EINVAL32;
2003 xhcip->xhci_regs_operoff = PCI_EINVAL32;
2004 xhcip->xhci_regs_runoff = PCI_EINVAL32;
2005 xhcip->xhci_regs_dooroff = PCI_EINVAL32;
2006
2007 xhci_fm_init(xhcip);
2008 xhcip->xhci_seq |= XHCI_ATTACH_FM;
2009
2010 if (pci_config_setup(xhcip->xhci_dip, &xhcip->xhci_cfg_handle) !=
2011 DDI_SUCCESS) {
2012 goto err;
2013 }
2014 xhcip->xhci_seq |= XHCI_ATTACH_PCI_CONFIG;
2015 xhcip->xhci_vendor_id = pci_config_get16(xhcip->xhci_cfg_handle,
2016 PCI_CONF_VENID);
2017 xhcip->xhci_device_id = pci_config_get16(xhcip->xhci_cfg_handle,
2018 PCI_CONF_DEVID);
2019
2020 if (xhci_regs_map(xhcip) == B_FALSE) {
2021 goto err;
2022 }
2023
2024 xhcip->xhci_seq |= XHCI_ATTACH_REGS_MAP;
2025
2026 if (xhci_regs_init(xhcip) == B_FALSE)
2027 goto err;
2028
2029 if (xhci_read_params(xhcip) == B_FALSE)
2030 goto err;
2031
2032 if (xhci_identify(xhcip) == B_FALSE)
2033 goto err;
2034
2035 if (xhci_alloc_intrs(xhcip) == B_FALSE)
2036 goto err;
2037 xhcip->xhci_seq |= XHCI_ATTACH_INTR_ALLOC;
2038
2039 if (xhci_add_intr_handler(xhcip) == B_FALSE)
2040 goto err;
2041 xhcip->xhci_seq |= XHCI_ATTACH_INTR_ADD;
2042
2043 mutex_init(&xhcip->xhci_lock, NULL, MUTEX_DRIVER,
2044 (void *)(uintptr_t)xhcip->xhci_intr_pri);
2045 cv_init(&xhcip->xhci_statecv, NULL, CV_DRIVER, NULL);
2046 xhcip->xhci_seq |= XHCI_ATTACH_SYNCH;
2047
2048 if (xhci_port_count(xhcip) == B_FALSE)
2049 goto err;
2050
2051 if (xhci_controller_takeover(xhcip) == B_FALSE)
2052 goto err;
2053
2054 /*
2055 * We don't enable interrupts until after we take over the controller
2056 * from the BIOS. We've observed cases where this can cause spurious
2057 * interrupts.
2058 */
2059 if (xhci_ddi_intr_enable(xhcip) == B_FALSE)
2060 goto err;
2061 xhcip->xhci_seq |= XHCI_ATTACH_INTR_ENABLE;
2062
2063 if ((ret = xhci_controller_stop(xhcip)) != 0) {
2064 xhci_error(xhcip, "failed to stop controller: %s",
2065 ret == EIO ? "encountered FM register error" :
2066 "timed out while waiting for controller");
2067 goto err;
2068 }
2069
2070 if ((ret = xhci_controller_reset(xhcip)) != 0) {
2071 xhci_error(xhcip, "failed to reset controller: %s",
2072 ret == EIO ? "encountered FM register error" :
2073 "timed out while waiting for controller");
2074 goto err;
2075 }
2076
2077 if ((ret = xhci_controller_configure(xhcip)) != 0) {
2078 xhci_error(xhcip, "failed to configure controller: %d", ret);
2079 goto err;
2080 }
2081
2082 /*
2083 * Some systems support having ports routed to both an ehci and xhci
2084 * controller. If we support it and the user hasn't requested otherwise
2085 * via a driver.conf tuning, we reroute it now.
2086 */
2087 route = ddi_prop_get_int(DDI_DEV_T_ANY, xhcip->xhci_dip,
2088 DDI_PROP_DONTPASS, "xhci-reroute", XHCI_PROP_REROUTE_DEFAULT);
2089 if (route != XHCI_PROP_REROUTE_DISABLE &&
2090 (xhcip->xhci_quirks & XHCI_QUIRK_INTC_EHCI))
2091 (void) xhci_reroute_intel(xhcip);
2092
2093 if ((ret = xhci_controller_start(xhcip)) != 0) {
2094 xhci_log(xhcip, "failed to reset controller: %s",
2095 ret == EIO ? "encountered FM register error" :
2096 "timed out while waiting for controller");
2097 goto err;
2098 }
2099 xhcip->xhci_seq |= XHCI_ATTACH_STARTED;
2100
2101 /*
2102 * Finally, register ourselves with the USB framework itself.
2103 */
2104 if ((ret = xhci_hcd_init(xhcip)) != 0) {
2105 xhci_error(xhcip, "failed to register hcd with usba");
2106 goto err;
2107 }
2108 xhcip->xhci_seq |= XHCI_ATTACH_USBA;
2109
2110 if ((ret = xhci_root_hub_init(xhcip)) != 0) {
2111 xhci_error(xhcip, "failed to load the root hub driver");
2112 goto err;
2113 }
2114 xhcip->xhci_seq |= XHCI_ATTACH_ROOT_HUB;
2115
2116 return (DDI_SUCCESS);
2117
2118 err:
2119 (void) xhci_cleanup(xhcip);
2120 return (DDI_FAILURE);
2121 }
2122
2123 static int
2124 xhci_detach(dev_info_t *dip, ddi_detach_cmd_t cmd)
2125 {
2126 xhci_t *xhcip;
2127
2128 if (cmd != DDI_DETACH)
2129 return (DDI_FAILURE);
2130
2131 xhcip = ddi_get_soft_state(xhci_soft_state, ddi_get_instance(dip));
2132 if (xhcip == NULL) {
2133 dev_err(dip, CE_WARN, "detach called without soft state!");
2134 return (DDI_FAILURE);
2135 }
2136
2137 return (xhci_cleanup(xhcip));
2138 }
2139
2140 /* ARGSUSED */
2141 static int
2142 xhci_getinfo(dev_info_t *dip, ddi_info_cmd_t cmd, void *arg, void **outp)
2143 {
2144 dev_t dev;
2145 int inst;
2146
2147 switch (cmd) {
2148 case DDI_INFO_DEVT2DEVINFO:
2149 dev = (dev_t)arg;
2150 *outp = xhci_get_dip(dev);
2151 if (*outp == NULL)
2152 return (DDI_FAILURE);
2153 break;
2154 case DDI_INFO_DEVT2INSTANCE:
2155 dev = (dev_t)arg;
2156 inst = getminor(dev) & ~HUBD_IS_ROOT_HUB;
2157 *outp = (void *)(uintptr_t)inst;
2158 break;
2159 default:
2160 return (DDI_FAILURE);
2161 }
2162
2163 return (DDI_SUCCESS);
2164 }
2165
2166 static struct cb_ops xhci_cb_ops = {
2167 xhci_open, /* cb_open */
2168 xhci_close, /* cb_close */
2169 nodev, /* cb_strategy */
2170 nodev, /* cb_print */
2171 nodev, /* cb_dump */
2172 nodev, /* cb_read */
2173 nodev, /* cb_write */
2174 xhci_ioctl, /* cb_ioctl */
2175 nodev, /* cb_devmap */
2176 nodev, /* cb_mmap */
2177 nodev, /* cb_segmap */
2178 nochpoll, /* cb_chpoll */
2179 ddi_prop_op, /* cb_prop_op */
2180 NULL, /* cb_stream */
2181 D_MP | D_HOTPLUG, /* cb_flag */
2182 CB_REV, /* cb_rev */
2183 nodev, /* cb_aread */
2184 nodev /* cb_awrite */
2185 };
2186
2187 static struct dev_ops xhci_dev_ops = {
2188 DEVO_REV, /* devo_rev */
2189 0, /* devo_refcnt */
2190 xhci_getinfo, /* devo_getinfo */
2191 nulldev, /* devo_identify */
2192 nulldev, /* devo_probe */
2193 xhci_attach, /* devo_attach */
2194 xhci_detach, /* devo_detach */
2195 nodev, /* devo_reset */
2196 &xhci_cb_ops, /* devo_cb_ops */
2197 &usba_hubdi_busops, /* devo_bus_ops */
2198 usba_hubdi_root_hub_power, /* devo_power */
2199 xhci_quiesce /* devo_quiesce */
2200 };
2201
2202 static struct modldrv xhci_modldrv = {
2203 &mod_driverops,
2204 "USB xHCI Driver",
2205 &xhci_dev_ops
2206 };
2207
2208 static struct modlinkage xhci_modlinkage = {
2209 MODREV_1,
2210 &xhci_modldrv,
2211 NULL
2212 };
2213
2214 int
2215 _init(void)
2216 {
2217 int ret;
2218
2219 if ((ret = ddi_soft_state_init(&xhci_soft_state, sizeof (xhci_t),
2220 0)) != 0) {
2221 return (ret);
2222 }
2223
2224 xhci_taskq = taskq_create("xhci_taskq", 1, minclsyspri, 0, 0, 0);
2225 if (xhci_taskq == NULL) {
2226 ddi_soft_state_fini(&xhci_soft_state);
2227 return (ENOMEM);
2228 }
2229
2230 if ((ret = mod_install(&xhci_modlinkage)) != 0) {
2231 taskq_destroy(xhci_taskq);
2232 xhci_taskq = NULL;
2233 }
2234
2235 return (ret);
2236 }
2237
2238 int
2239 _info(struct modinfo *modinfop)
2240 {
2241 return (mod_info(&xhci_modlinkage, modinfop));
2242 }
2243
2244 int
2245 _fini(void)
2246 {
2247 int ret;
2248
2249 if ((ret = mod_remove(&xhci_modlinkage)) != 0)
2250 return (ret);
2251
2252 if (xhci_taskq != NULL) {
2253 taskq_destroy(xhci_taskq);
2254 xhci_taskq = NULL;
2255 }
2256
2257 ddi_soft_state_fini(&xhci_soft_state);
2258
2259 return (0);
2260 }